Club 80-90 Forums

Hey all, I’ve got a 1982 air cooled t25 and am looking at different companies for conversions. Lots of the topics on here with info are from a good...

Hi everyone. Although i knew my van needs some specialist welding and underbody repairs this has been  confirmed after taking the van to South West...

i already use some basic chopping board spacers on the back to bring up the saggy bottom, but front spacers are more involved than that, being not...

Just a quick heads-up to anyone running a VAG drive-by-wire engine including any 1993-2005 TDI (and probably later), or petrol engine from ~2000...

Quick tip from Covkid on preventing engine bay wires from going brittle. I use the same stuff when restoring valve radios because of its...

The textured ceiling covering on my Kameo is cracked and splitting around the central vent, probably due to past water ingress. Has anyone replaced...

I need some help please,
I have the above, have had the timing belt sorted by my local guru but we are struggling to get the correct v belt size for...

So discovered it's not a good idea...

After having the engine out (1.9 DG) to sort out the exhaust studs, decided to replace clutch plates, and have...

I've decided to rebuild a spare dizzie that has been gathering dust in a box. I stripped it down years ago trying to unsuccessfully fix a faulty hall...

Hi,

I've got a original westfailure table which swings out from above the cupboards. last year a washer (internal tooth spring washer I...

Hi All, 

Looking for some advice on my T25 westfailure high top. The groove the groove the pull out bed runs in had a plastic trim on the top and...

Hi guys

I have a leak at the governor seal on my 1988 auto gearbox. Question is can I replace it without draining ATF? Many thanks!

Hey there, can you look over my timing setup?
I'm having problems with the van stumbling under acceleration, with low power. But I want to make sure...

Morning all!

I’m after some help with the r&r bed hinges.

I’ve purchased them 2nd hand and they look
Like the justkampers hinges. However, they...

Help! Really struggling to find someone to set up my carb. Does anyone have any recommendations in the Leicestershire area?

Thanks

Sent from my...

Hi, I have wired up an aftermarket (Eluto, so might as well not have any brand) oil pressure gauge.

It seems to give reasonable values, but that's...

I have asked a question on the alternative engine site but really my query is not specific to my AAZ.

My gearbox will be with Aidan soon for some...

Currently on a 5 week uk tour with work dotted in between . van has been faultless untill yesterday when temp gauge became intermittent and lower...

Wondering if anyone has experience of these batteries. They're way cheaper than good quality LiFePO4 ones and would save a lot of space. One 125Ah...

My gearbox is going to Aidan’s for some tlc next month and thought was to get him to change the shaft so that I can fit a dual mass flywheel...

Moved to sales.

Hi all
My T25 is now in need of some minor rust repairs, seams maybe wheel arches etc., nothing too serious. Has anyone any recommendations in or...

Hi all

I have fitted a new waterpump to my 1.9 dg but it didn't come with the sealing bung for the extra hole .
I havent been able to locate...

1986 Leisuredrive fitted with a 97 1Y engine. After a major "cock" up I need to get the inlet manifold off. Can it come off without removing the...

Just got a second t3 caravelle last week. factory fitted electric windows, foglights in the second grill and it's best feature: the sliding rooftop....

Iv just changed the old Cork gasket 3 piece on the rocker cover for the newer single piece rubber gasket.. But it appears to still be weeping in the...

Good afternoon all, hope everyone is well 👍

I've noticed a bit of a grinding/rubbing noise when underload in reverse (up a gradient, or when trying...

Well I thought I'd just share this as you just never know it might help someone else as well!

I have been having trouble with shifting gear for...

Apologies for such a simple question but I'm stumped. Does any one know what kind of bulb fits in the cigarette lighter of a late T25?
The bulb is...

The gas burner on my 3 way electrolux fridge (RM212F)
Needs replacing.
Mesh disintegrated and jet stuck, wont come out.
Wheres the best place to...

Reading recent articles associated with this and an old one by Itchyfeet, how important is this unit and how can it be tested in situ to see if it is...

Hi Everyone,

Can anyone recommend a mobile habitation service? I want to get my gas and fridge serviced.

Thanks,
Tim.

Posted this before and got good advice that the Sun would cure it. Tried this but appears not to work. Cleaned it the other day with Mould remover...

Hi everyone, I have a slow diesel leak from my throttle arm that I want to fix on my 1.7ky engine. I have been advised to change the o ring and bush...

Hi,

Would anyone know what this part is called (circled in red) ?

It seems like a water inlet and Im trying the find the flap but dont know what...

Hello, I just spotted this social enterprise based in Exeter who reupholster vehicles and campers. Worth a look, a good cause and online quotes...

I have just been looking at the design of the end-float shims behind the flywheel for a DJ engine and have been wondering how they are supposed to...

Where would be the best place to install speakers in the back of an Autohomes Komet?

I've got an image in my head of an enclosure I could attach to...

With somewhat of a light at the end of the tunnel I have started at preparing my Camper for the first trip of the year.

As it’s been sitting outside...

Is there anyone from stoke on Trent only we need a bit of help with a T25 2000cc cu engine timing and valve set up...we think the dizzy is either...

Are normal red powder 1kg extinguishers best stored vertical? Is there any reason why they couldn't be stored horizontally?

Does it matter? Am I...

Hi All,

My van had the accelerator cable replaced before I bought it, and it is not quite right:

When I start up the engine revs slightly and stays...

Auto Gearbox Throttle Lever Leak

Hi all knowledgeables! 

I'm sorting out the long list of issues on my van, hopefully in time for some summer...

My LH Heat Riser is corroded through & needs replacing.

The bolts securing the bracket to the tinware are well corroded and inaccessible & I'm...

Hello folks! Has anyone fitted the dipstick tube seal and washer to the Jx engine? How far down does the seal and washer go??

Have got some decals from Brickwerks.  Now I am really worried about messing up applying them.

Does anyone have a step by step guide at all please...

Seeking the male and female three round pin VW connectors. Or equivalent aftermarket. Must be compatible with genuine VW connectors
Brickwerk out of...

Does anyone know of a two ring gas hob that would replace the 'Fellows' one in an Autosleeper. I've looked every where and can't find one to fit.

Hi,
I've had a look across the forum but couldn't find these referenced, so hoping someone can help.

I'm thinking of getting a set of these for my...

Hi, been looking to get a louvred side windindow for my 81 holdswoth conversion, it was an optional extra when new so thought I’d try a get hold of...