Search results

Ok, instructions then. == Right let's go == ...

It frustrates me often when an "internet friend" on here (and elsewhere) has a computer that needs a good coat of looking at, becaus ...is, and believe me, with these more recent sata drives, it is VERY common, then the rest of the servicing procedure will work the drive very hard and in th ...

'''Toolsntat:''' On mine I have 2 rubber grommets that those 2 pins go into and not bare metal. Are your grommets missing? ...er that I had rattly steering for a while, until one day it went clunk and then floppy @@ ...

Post it here good or bad... ...ey wanted a (motor) engineer's report that it had been done properly. They then were happy and it's a 1.9 now, for DVLC and Insurance purposes. Cannot resp ...

These days, we run items that need a lower supply than 12.5V, and if you've got something A great video explaining the principles can be found here: https://www.youtube.com/watch?v=GSzVs7_aW-Y ...

...seat runners off and remove the seat height adjustment lever and workings. Then space and rebolt the runners to the same holes as on the passenger seat. ...ster lever needs removing and reshaping to the new narrower dimension, and then re-attatching. The the seat needs bolting back to the runners with the spac ...

...more metal (the filler rod) - this typically happens on vertical seams and we call it chasing the onion. ...out MIG is there is no need to strike an arc. You can just about point and go. ...

...ft to move. Can it only move in & out? Can it twist? How much movement are we talking? ...en key in the roll pin hole and some gear oil in the diff lock switch hole then gently reaming it back into operation with a straight in-out motion doesn't ...

...ap B&Q brickwork sealer works too), we're talking clear patio type sealers here, not varnishes. If you don't chamfer it properly with a hooked blade, then definitely use a flooring sealer around the edges, esp. at the sliding door ...

...(March 2015) In retrospect, things have moved on somewhat and rather than go to the trouble of soldering components as below, it would be far simpler to ...e) 2 x 5watt bulbs. They're not bad I guess, but the bulbs will ultimately go and usually after they've already become blackened. I decided to keep the o ...

...the summer in hot climes. I certainly don't want to have a valve seat let go and stuff a cylinder and head. A cylinder head temp gauge under spark plug available here @ airworld [http://www.airworlduk.com/] ...

...ro ones aren't much different to be honest. They're cast though, so don't go trying to weld the new bush in, OK? The red arrow shows the tag-weld that's holding the bush in the wishbone. We're gonna cut that off with an angle grinder as the bush ain't coming out wi ...

...on box left side front of engine as this supplies the fuel and ecu relays, then check the outputs from both the relays, if the ecu doesn't get it's ignitio Then: ...

...y interior trim panels so you can see whats going on in there. If its bad, then almost all of this article will apply and you'll be cutting as shown. If it ...ut, and Chickenkoop who can be seen welding), so this project is presented here on the basis that you have limited kit and/or experience but want to try or ...

...re it meets windscreen. This evidence is not always there but they ALL rot here and unless screen has been out recently, I can guarantee you'll find rot in ...runs, completely unseen and down into the corners where it has nowhere to go whatsoever until it finally rots the metal (see photo below) and has a rout ...

...encouragement from my mate Del,who likes his vans,the decision was made to go for open heart surgery in January this year! ...original connectors hacked about.This meant removal of the fuel tank,where we noticed the sellers top skills had been put to good use!!(The filler neck h ...

...c climate control, although we didn't expand the project further. However, we couldn't see why PWM wouldn't work on the blower motor and as you'll see be ...ted briefly, the motor will still spin on a little, and that whats at work here - plus there is the luxury of being able to set any speed you want from zer ...

...ob ourselves because I was too tight to pay for the mechanic and I thought we should learn something about the van.'' '''How we did it''' ...

...ts on this site how relatively easy the engine and gearbox were to remove, we pressed ahead. ...ith pictures which I hope maybe of use to others who are tempted to have a go. ...

...driver to initially loosen. Screw back in a bit, repeat wire-brush/penoil, then work them out slowly. Once they're a bit loose can spray threads from front '''As we all know, half heartedly attacking with wrong screwdriver or not enough bod ...