Mercedes alloys and wishbone clearance

All things round and their alignment to your direction of travel

Moderators: User administrators, Moderators

Post Reply
mrbodly
Registered user
Posts: 134
Joined: 21 Oct 2013, 22:21
80-90 Mem No: 13264
Location: Colchester, Essex

Mercedes alloys and wishbone clearance

Post by mrbodly »

Hi all

I'm not new to the forum having previously owned an 82 Aircooled Joker. I've recently purchased a 1990 Westy Atlantic...
Image

I've overhauled the suspension amongst other things. I've fitted AVO shocks and 50mm springs and replaced all the bushes with powerflex items. I'm now at the point of getting the alignment set at my local garage. However a previous owner has fitted Mercedes alloys, 7.5 x 16 et41 with 215/65r16 tyres on the rear and 215/55r16 tyres up front and 10mm spacers all round. I think the wheels look great but I'm concerned at the amount of clearance between the front tyres and upper wishbones. There is approx 5mm clearance. Should I be concerned?

ImageImage
I like the alloys and the tyres have a decent amount of tread. I have considered swapping the 10mm spacers for 15mm to increase the clearance but I'm concerned this would push the tyre outside the wheel arch. I've also thought about sourcing some VW Carat alloys but these seem fairly hard to get hold of and expensive when they do, plus the cost of fitting new tyres and wheel studs etc.

Image

I'm interested in the thoughts of those on the forum. My previous van had standard wheels and this is my first experience of a vehicle with modified wheels. As much as I like the Merc alloys I'd like the van to be safe. Am i worrying unnecessarily?

Thanks
Myles

User avatar
clift_d
Registered user
Posts: 3539
Joined: 04 Oct 2012, 23:51
80-90 Mem No: 11695
Location: Hackney innit

Mercedes alloys and wishbone clearance

Post by clift_d »

As long as you’ve always got a few mm clearance and it doesn’t touch anywhere when turning from lock to lock then i think it should be fine. Remember that it’s probably done a fair few miles like that without issue before you got it. If you did decide to space it out further you’d risk creating other issues for yourself such as your tyres potentially touching your arches.
1988 LHD T25 1.6TD Westfalia Club Joker Hightop syncro

Alfredo
Registered user
Posts: 244
Joined: 03 Oct 2024, 19:50
80-90 Mem No: 17766
Location: Worcestershire

Re: Mercedes alloys and wishbone clearance

Post by Alfredo »

Carat wheels are worth it.

Image

Image
1988 Autosleeper Trooper pop top 1.9DG
2003 MG TF 135 Cool Blue

User avatar
slowcoach
Registered user
Posts: 1689
Joined: 06 May 2010, 10:23
80-90 Mem No: 8892
Location: West Yorkshire
Contact:

Re: Mercedes alloys and wishbone clearance

Post by slowcoach »

I wouldn't worry about it. As said, it may have done a lot of miles like that already.

I have 16" mercedes tolliman wheels for several years, and it looks the same.

Carrot wheels are nice but very small 14", and a similarly small choice of tyres to put on them.

Relax and enjoy !
===================
1984 TRAKKA Conversion Subaru EJ20 5 Speed

silverbullet
Trader
Posts: 17908
Joined: 08 Jun 2009, 09:51
80-90 Mem No: 6908
Location: Surrey Syncronaut #156
Contact:

Re: Mercedes alloys and wishbone clearance

Post by silverbullet »

You have clearance off both the wheelarch and the wishbone, they fit.
ET is a very misunderstood subject, too many get fixated on the OEM backspace offset (the ET measurement in mm) when what really matters is that you get as much tyre inboard as possible if they are anything over the OEM max width of 6" (which this wheel does) and no arch or seatbox fouling under any condition.
1985 Oettinger 3.2 wbx-6 Caravelle RHD syncro twin slider. SA Microbus bumpers, duplex winch system, ARC 7X15 alloys,
"Schrödinger's syncro"
Syncronaut #156

Post Reply