Eber b1l

The Tardis factor (interiors , awnings, roofs etc)

Moderators: User administrators, Moderators

Locked
User avatar
bikermike87
Registered user
Posts: 389
Joined: 24 Oct 2009, 21:16
80-90 Mem No: 7559
Location: New Brighton, Wirral

Eber b1l

Post by bikermike87 »

Hi there,

I've just bought a eber b1l and despite checking the installation document on the wiki, I'm not sure if I am doing something wrong or I have bought a faulty one.

A: is connected to the fuel pump

B: is connected to the battery, reading 13.5v


Image

When I connect C with D the fan blows for about 20-40 seconds and then stops. The fuel pump feels as though it pumping on a pulse, but no fuel is being sucked up...

Any ideas?!
https://www.facebook.com/ChefCampers/
1991 Syncro Westfalia Atlantic 2.1MV

User avatar
Oldiebut goodie
Registered user
Posts: 7399
Joined: 18 Apr 2008, 01:19
80-90 Mem No: 11135
Location: Eastern Angle

Re: Eber b1l

Post by Oldiebut goodie »

You have to prime the fuel line first or you may need 10-20 startup attempts to do it with the heater. If the pump has been dry for a long time a squirt of wd40 or fuel in the inlet can help. Ensure that the filter in the pump inlet is clear also.
1.6D 2019 VW T-Cross
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶

billybigspud
Registered user
Posts: 635
Joined: 11 Mar 2011, 15:59
80-90 Mem No: 9454
Location: southampton

Re: Eber b1l

Post by billybigspud »

Whip the glow plug out and connect one of the wires that go to the pump to -ve and the other one to +ve and keep making and breaking the connection so the pump keeps clicking/pumping. Eventually you will see some fuel come from the jet inside where the plug came from. You will know it is primed then. Mine would not pull through the filter as it had been sat a while so I took the hose off between it and the pump and gave it a suck. Tasted like "pooh" but pulled it through enough to give the pump a chance.
There is probably a better way but it worked for me.

User avatar
Oldiebut goodie
Registered user
Posts: 7399
Joined: 18 Apr 2008, 01:19
80-90 Mem No: 11135
Location: Eastern Angle

Re: Eber b1l

Post by Oldiebut goodie »

^^^^^^Don't prime it that way - there is a risk of frying the ecu!!!
Disconnect the wiring from the pump and use a 12v source to make and break the power at the pump with no connection to the heater. (polarity is immaterial)
1.6D 2019 VW T-Cross
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶

User avatar
bikermike87
Registered user
Posts: 389
Joined: 24 Oct 2009, 21:16
80-90 Mem No: 7559
Location: New Brighton, Wirral

Re: Eber b1l

Post by bikermike87 »

Hi guys,

Thanks for the help.

I've primed it by just connecting the pump directly to the battery, nothing else. Fuel was squirting away, pumped it up into the eber and then wired everything up like last time.

Now I don't have anything, no fan :-(

Is it possible I have flooded the eber with fuel and this auto stops it?!

Is there anything I can check if I open the ecu?
https://www.facebook.com/ChefCampers/
1991 Syncro Westfalia Atlantic 2.1MV

User avatar
Oldiebut goodie
Registered user
Posts: 7399
Joined: 18 Apr 2008, 01:19
80-90 Mem No: 11135
Location: Eastern Angle

Re: Eber b1l

Post by Oldiebut goodie »

bikermike87 wrote: Is it possible I have flooded the eber with fuel and this auto stops it?!
No!

Don't open the ecu. Nothing for you in there! :lol:
User error prime cause. Go back to what you have changed/touched. Thermostat calling for heat? (what controller are you using?)
Double check your connections, loose fuses, voltage.
1.6D 2019 VW T-Cross
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶

User avatar
bikermike87
Registered user
Posts: 389
Joined: 24 Oct 2009, 21:16
80-90 Mem No: 7559
Location: New Brighton, Wirral

Re: Eber b1l

Post by bikermike87 »

I'm just using a universal switch, it says thermostat is optional. :?

Checked polarity and voltage and it's feeding the ecu, fuse in ecu is fine.

Worried I have cooked my ecu :(
https://www.facebook.com/ChefCampers/
1991 Syncro Westfalia Atlantic 2.1MV

billybigspud
Registered user
Posts: 635
Joined: 11 Mar 2011, 15:59
80-90 Mem No: 9454
Location: southampton

Re: Eber b1l

Post by billybigspud »

Oldiebut goodie wrote:^^^^^^Don't prime it that way - there is a risk of frying the ecu!!!
Disconnect the wiring from the pump and use a 12v source to make and break the power at the pump with no connection to the heater. (polarity is immaterial)
Surely that is what I just said!!!!!!!! Did I mention the ECU? No, I said the wires that go to the pump. READ THE POST. Idiot.

User avatar
Oldiebut goodie
Registered user
Posts: 7399
Joined: 18 Apr 2008, 01:19
80-90 Mem No: 11135
Location: Eastern Angle

Re: Eber b1l

Post by Oldiebut goodie »

Numbskull! That is not what you said ! If you want to get into a slanging match over your inability to express yourself clearly go ahead - I am more than ready to oblige you.
There is no mention in your post of disconnecting the pump from the ecu. Read it again.

billybigspud wrote:Whip the glow plug out and connect one of the wires that go to the pump to -ve and the other one to +ve and keep making and breaking the connection so the pump keeps clicking/pumping. Eventually you will see some fuel come from the jet inside where the plug came from. You will know it is primed then. Mine would not pull through the filter as it had been sat a while so I took the hose off between it and the pump and gave it a suck. Tasted like "pooh" but pulled it through enough to give the pump a chance.
There is probably a better way but it worked for me.

Another idiot on the foe list. Image
1.6D 2019 VW T-Cross
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶

Locked