Pierburg 2E3 carb conversion - Weber 34DAT

Big lumps of metals and spanners.

Moderators: User administrators, Moderators

Locked
platty
Registered user
Posts: 0
Joined: 14 Oct 2009, 17:56

Pierburg 2E3 carb conversion - Weber 34DAT

Post by platty »

Hi everyone - I am new to the forum and have a problem with a carb conversion. Have switched from a Pierburg 2E3 to a Weber 34DAT from Just Kampers. All works well except the choke. On cold start when the accelerator is pressed the choke engages and the engine starts everytime revving nicely, but as soon as I press the accelerator again, to drive off, the choke seems to disengage and the revs drop very low, almost stalling. When engine up to temperature all is well. Engine is 1.9 watercooled DG, 1990. Any ideas anyone :(

waltraud
Registered user
Posts: 716
Joined: 27 Aug 2008, 12:59
80-90 Mem No: 5824
Location: London

Re: Pierburg 2E3 carb conversion - Weber 34DAT

Post by waltraud »

Leave it to idle on choke for longer before you set off. Seriously though, is the idle set a bit low for when tis warmed up, around 900rpm? If a bit low it may want to die off choke when cold, perhaps you can alter the length of time before choke cuts out? I'm aure there will be some web info on setting her up? Good luck. NB What have you done with the pierburg?

cheers

Tim
1983 1.9 Ivory Westy Joker

User avatar
VWCamperfan
Registered user
Posts: 993
Joined: 08 Jul 2007, 19:47
80-90 Mem No: 4000
Location: Sheerness, Kent.

Re: Pierburg 2E3 carb conversion - Weber 34DAT

Post by VWCamperfan »

Re-adjust the choke so it stays on longer. Sounds like just a small amound of heat is taking the choke off too soon. Loosen 3 small screws on choke body and rotate to adjust. Rotate in directon of choke movement when it's closing.
Mark.

I'm Not A Complete Idiot... Some Bits Are Missing!

1.6 Modified CT engine.

platty
Registered user
Posts: 0
Joined: 14 Oct 2009, 17:56

Re: Pierburg 2E3 carb conversion - Weber 34DAT

Post by platty »

Thanks for info.......Pierburg Ebayed :D

johny342
Registered user
Posts: 90
Joined: 19 Jun 2010, 13:30
80-90 Mem No: 8339
Location: york

Re: Pierburg 2E3 carb conversion - Weber 34DAT

Post by johny342 »

hello! im new to the forum too! im changing my pierburg to a weber is it easy to do? my weber came with a K+N FILTER should i leave this on or put standard airbox back? many thanks.

User avatar
toomanytoys
Trader
Posts: 2872
Joined: 11 Oct 2005, 18:37
80-90 Mem No: 41
Location: Boston area, South Lincolnshire

Re: Pierburg 2E3 carb conversion - Weber 34DAT

Post by toomanytoys »

Mixed bag of results....
Most have had issues when using them.. like worse fuel economy and no better running.. several have had to get them set up on a rolling road to make them work properly too..
They dont seem to give any better performance either...

A well serviced, setup and working 2E3 works very well indeed... a bodged dirty and broken one is carp... :wink:

johny342
Registered user
Posts: 90
Joined: 19 Jun 2010, 13:30
80-90 Mem No: 8339
Location: york

Re: Pierburg 2E3 carb conversion - Weber 34DAT

Post by johny342 »

thanks for that info. i will try the weber and if no better try another pierburg i have. mine runs ok but flat spot just above tickover really annoying! had a go in my mates with pierburg and ran faultless.

Locked