New engine - seems to run hot...

Big lumps of metals and spanners.

Moderators: User administrators, Moderators

Locked
User avatar
markbikerider
Registered user
Posts: 47
Joined: 07 Oct 2009, 20:05
80-90 Mem No: 7486
Location: Lancaster

New engine - seems to run hot...

Post by markbikerider »

Hello folks,
I have just had a TES 2.1 DJ recon engine fitted to my bus last week. During this running in phase, the temp gauge is well over to the right, pretty much on the cusp of the fan kicking in all the time (not just in town traffic, but gently coasting down A roads). I know it's been quite hot of late, but is this normal, as I don't remember my last engine running quite so hot (although it was usually to the right of centre)? The temp sender is off the old engine (2.1 the same), but is only a few months old and ordered from Brickwerks so should be the correct one.

Anyone else running hot during these summer months as I really can't think what it could be (the radiator is working and the garage even replaced the water pump, so it can't be that..)

Thanks, as always, Mark
As Neil Young once said 'Rust never sleeps...'

jason k
Registered user
Posts: 938
Joined: 13 Nov 2005, 09:35
80-90 Mem No: 1959
Location: aberdare south wales

Re: New engine - seems to run hot...

Post by jason k »

How's the water levels?

Perhaps it needs a bleed again
98 Westfalia James Cook

User avatar
AdrianC
Registered user
Posts: 2975
Joined: 29 Dec 2010, 21:57
80-90 Mem No: 9144
Location: Living in Hay whilst the Sun pours down.
Contact:

Re: New engine - seems to run hot...

Post by AdrianC »

Remember, the "normal band" of the engine temperature is controlled by two things.

At the bottom end, the thermostat. When the coolant's too cool, this closes, allowing the thermostat to bypass the rad and warm up.
At the upper end, the fan switch. When the coolant's too hit, this turns the fan on, reducing the temp of the coolant heading back to the engine.

If it's sitting just shy of the fan coming on, on a hot day, with the fan cycling gently - that's in the normal band. Nothing to worry about.

It's entirely possible that, with new internals still bedding down, friction in the motor's a bit higher than it was in your old, slack and slappy one. That's not necessarily a bad thing, but will also contribute to heat generation.
A year and a half living in a Westy hightop... http://www.WhereverTheRoadGoes.com" onclick="window.open(this.href);return false;

User avatar
markbikerider
Registered user
Posts: 47
Joined: 07 Oct 2009, 20:05
80-90 Mem No: 7486
Location: Lancaster

Re: New engine - seems to run hot...

Post by markbikerider »

Well that's a relief - thanks for the replies :ok
As Neil Young once said 'Rust never sleeps...'

California Dreamin
Registered user
Posts: 2673
Joined: 03 Apr 2007, 12:54
80-90 Mem No: 8386
Location: Nottingham

Re: New engine - seems to run hot...

Post by California Dreamin »

Mark...was the van originally a 2.1 (I know you said the old engine was) just that the 1.9's did have a thinner radiator.
Also
I would be tempted to fit a new radiator fan switch, after fitting a new one on mine the fan definitely kicks in lower on the gauge..quite reassuring TBH.

Martin
1989 California 2.1MV

User avatar
markbikerider
Registered user
Posts: 47
Joined: 07 Oct 2009, 20:05
80-90 Mem No: 7486
Location: Lancaster

Re: New engine - seems to run hot...

Post by markbikerider »

Hi Martin - good to hear from you! It was around 12 months ago we were all in Berlin - Happy times! Thanks for the advice. I think I'll order a new fan switch then for peace of mind.
Cheers Mark
As Neil Young once said 'Rust never sleeps...'

Locked