Propex boxed in & 90 degree pipe elbows?

The Tardis factor (interiors , awnings, roofs etc)

Moderators: User administrators, Moderators

Locked
User avatar
toolsntat
Registered user
Posts: 1112
Joined: 28 Oct 2005, 22:41
80-90 Mem No: 644
Location: Leicesterish

Propex boxed in & 90 degree pipe elbows?

Post by toolsntat »

Anyone used a cheaper alternative?
How about rainwater downpipe :?:

Andy (yes, I am finally fitting the heater 8) :wink: )
Last edited by toolsntat on 24 May 2013, 08:50, edited 1 time in total.
------------------
"GOT ANY OLD TOOLS??"
"WANT ANY OLD TOOLS??"
WANTED old treadle lathe please......
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
1980 2.0L Aircooled Blue Hightop Holdsworth Villa Camper
2002 White 2.0l 280 td swb hightop Tranzit works van

Plasticman
Trader
Posts: 8072
Joined: 12 Oct 2005, 20:55
80-90 Mem No: 1948
Location: lincolnshire

Re: Propex 90 degree pipe elbows?

Post by Plasticman »

andy,the flexible stuff does form as near as damit a 90' bend and dont deform,
mm

User avatar
toolsntat
Registered user
Posts: 1112
Joined: 28 Oct 2005, 22:41
80-90 Mem No: 644
Location: Leicesterish

Re: Propex boxed in & 90 degree pipe elbows?

Post by toolsntat »

Thanks Mike, have used some old AQUAVAC hoover hoses in the end :idea: 8)

Noticed the body warms up , so will it harm the unit if it all gets stowed in an insulated housing?

Andy
------------------
"GOT ANY OLD TOOLS??"
"WANT ANY OLD TOOLS??"
WANTED old treadle lathe please......
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
1980 2.0L Aircooled Blue Hightop Holdsworth Villa Camper
2002 White 2.0l 280 td swb hightop Tranzit works van

Plasticman
Trader
Posts: 8072
Joined: 12 Oct 2005, 20:55
80-90 Mem No: 1948
Location: lincolnshire

Re: Propex boxed in & 90 degree pipe elbows?

Post by Plasticman »

dont think so , my propex(older red unit)is under the bed/seat and covered with a ply lid etc and this is insulated too, then the ducting goes to a Y piece and through the cuboards etc, not had any probs over 5 + years, duct gets luke warm at most
the vacv hose .im not sure about, try it and run it up and see. it will also depend on how close it is to the heater
mm

User avatar
ghost123uk
Registered user
Posts: 6855
Joined: 10 Mar 2006, 10:15
80-90 Mem No: 2585
Location: John in Malpas, in the very S. W. part of Cheshire.
Contact:

Re: Propex boxed in & 90 degree pipe elbows?

Post by ghost123uk »

I have some spare Propex duct hose in the garage if you need some.

My (red) Propex is also under the bed, surrounded by tat :shock: - it has been fine for a year of use and does not seem to get more than "cup of tea" hot.
Got a new van, but it's a 165bhp T4 [shock horror] Accurate LPG Station map here

User avatar
Oldiebut goodie
Registered user
Posts: 7481
Joined: 18 Apr 2008, 01:19
80-90 Mem No: 11135
Location: Eastern Angle

Re: Propex boxed in & 90 degree pipe elbows?

Post by Oldiebut goodie »

On Webastos I use hose rated at 150 degrees or above - I don't know what the heat output on Propexes is but I would still be wary of using anything less. By all means use it on the inlet size. I have melted various plastic items on the bench when they have been left near the outlets of Webastos being tested. Proper silicone ducting is cheap enough in the short lengths that are normally required and will form a tight 90 degree bend.
1.6D 2019 VW T-Cross
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶

User avatar
Aidan
Trader
Posts: 6991
Joined: 11 Oct 2005, 19:21
80-90 Mem No: 742
Location: Llanfyllin, mid Wales : )
Contact:

Re: Propex boxed in & 90 degree pipe elbows?

Post by Aidan »

propex is supposed to have 25mm air gap around the outer case when installed
they aren't the quietest thing in the world but if you try to insulate them to deaden the sound you could end up cooking the internal circuit board - they are only cooled by the induction air being drawn in around the case

Plasticman
Trader
Posts: 8072
Joined: 12 Oct 2005, 20:55
80-90 Mem No: 1948
Location: lincolnshire

Re: Propex boxed in & 90 degree pipe elbows?

Post by Plasticman »

i have the old bugger with no lecky inside it has the sepperate box of tricks, but valid point, however it does have through passage :lol: of air :rofl
mm

User avatar
CovKid
Trader
Posts: 8411
Joined: 30 Apr 2006, 13:19
80-90 Mem No: 3529
Location: Ralph - Coventry (Retired)
Contact:

Re: Propex boxed in & 90 degree pipe elbows?

Post by CovKid »

I went to Jacksons of Arley (big Caravan place). They had hose that matched, the right stuff, and it was cheap as chips. As said, it'll go where you want to put it. Try a caravan retailer.
Roller paint your camper at home: http://roller.epizy.com/55554/" onclick="window.open(this.href);return false; for MP4 download.

Locked