VW Part Number Request Please - Lugnut/Cagenut (see photo)

[Mickyfin]

Basically these are secured to the chassis in the front underbody, and then a bolt and washer screw into them to secure the front Syncro bash plate in place.

Does anyone know the VW part number please?

Photo thats to Syncropaddy.

I have looked on ETKA, but can only find the self tapping type bolt, (Speed bolt?) which member Lloydy has on his Syncro bash plate. I'm pretty sure these I have removed are OEM, fitted to my 1992 Syncro Caravelle.

If anyone can help, that would be ace, thanks!

[lloydy]

- N 01021527
hexagonal head bolt
M6X15 /
- N 01166615
washer
6,4X18X1,6 /

It's a bit vague on ETKA but these seem to be the bolt and washer?

[Mickyfin]

Cheers mate, I will cross reference those part numbers on my ETKA, and if they are the ones, I will go armed to VW tomorrow

Did you find an illustration in your ETKA? Syncropaddy has got that image from somewhere, and Im guessing possibly a trade ETKA?

[lloydy]

Yes, there is a diagram in ETKA it is in the pedal section

It's only a M6 by 15mm bolt so you could source that from anywhere

[Mickyfin]

True, I can get the bolts and washers locally, but its those darn clips. I'm hoping member Max and Caddy can help as they purchased some of these clips from VW four months ago. Maybe I will PM Max

[lloydy]

I'm going to get some from the link you were given

[Mickyfin]

Not been given a link yet

[lloydy]

You were, cuz thats where i got it from
http://catalogue.jetpress.com/Products. ... Template=F" onclick="window.open(this.href);return false;
and the thread with a bit of info
https://club8090.co.uk/forum/viewtopic.p ... 64&start=0" onclick="window.open(this.href);return false;

[Mickyfin]

Ah, didn't realise that the image was a link lol

http://catalogue.jetpress.com/Products. ... Template=F" onclick="window.open(this.href);return false;

Nice 1

Doh, can't find how to order. I will see what I can find tomorrow in a couple of hardware stores, but it nothing, then will check to see if Mr Baxter has any, and if not, then Jetpress it is, however, I want to refit bash plate asap really.

[syncropaddy]

I think the side rows of nuts and bolts are M6 and the front row are M8

[max and caddy]

i will go into parts in the morning and peck sombodys head with some obscure part for a poopy old van...again...and post up the part number...if i get time, got the dash apart on v10 pheaton at the mo and its like a living hell!!

[Mickyfin]

I think the side rows of nuts and bolts are M6 and the front row are M8

I found that the front row are M6, same as the sides, its the rear row that are M8

i will go into parts in the morning and peck sombodys head with some obscure part for a poopy old van...again...and post up the part number...if i get time, got the dash apart on v10 pheaton at the mo and its like a living hell!!

Ok my friend, that would be awesome! Good luck with your dash.

[lloydy]

i will go into parts in the morning and peck sombodys head with some obscure part for a poopy old van...again...and post up the part number...if i get time, got the dash apart on v10 pheaton at the mo and its like a living hell!!

So, you work for VW?

[Mickyfin]

He does yes

[Mickyfin]

Well, I finally found a place that sell those lugnuts.

€21.90 for a pack of 20 Galvanized



Then went elsewhere, and picked up the following Stainless stuff..

10 M6 Short bolts
10 M6 Washers
3 M8 Short bolts
3 M8 Washers

Only 61 cents for those. Motonet here in Finland has to be one of the most expensive motor stores around, would normally avoid, but needs must I guess.