Torque Converter Starter Ring

Big lumps of metals and spanners. Including servicing and fluids.

Moderators: User administrators, Moderators

User avatar
maxstu
Registered user
Posts: 5359
Joined: 07 Feb 2008, 01:05
80-90 Mem No: 3946
Location: Margate

Torque Converter Starter Ring

Post by maxstu »

Has anyone replaced the starter ring?. Is it possible? If so, how did you manage to weld it true? Any tips please?
Posting on behalf of a mate. His 2.1 auto is making terrible noises from the starter and often doesn't engage. He takes a 30mm spanner to the crank pulley and rotates engine a bit to move starter gear away from worn part of the ring gear. Then it starts. He wants to rectify this before a trip to Spain next year. Apparently the torque converter ring has a habit of stopping in the same place? Can't see how, though.

Regards
Stuart

Image
MaxStu
1987 2.1 Automatic Carb/LPG Autosleeper.
"Blissfully happy in your presence".

silverbullet
Trader
Posts: 17901
Joined: 08 Jun 2009, 09:51
80-90 Mem No: 6908
Location: Surrey Syncronaut #156
Contact:

Re: Torque Converter Starter Ring

Post by silverbullet »

All starter ring gears on flywheels are pre-machined, quite concentric and shrink fit i.e. remove mechanically (flog it off) or drill a axial hole through the gear and split the gear to remove, then the new gear is evenly heated up ( lay it flat on white cement blocks and use a big propane lamp)
Ring gears grow A LOT when heated so don't panic, it doesn't need to be red hot just enough to get the sweat off and boil your spit.
Swiftly pick it up and place it on to the flywheel shoulder and within 30 seconds it will have grabbed it.
Torque converter shouldn't be any different but you'll have to cut the welds with a skinny disc and dress off anything remaining with care.
Or...got to a TC specialist!
1985 Oettinger 3.2 wbx-6 Caravelle RHD syncro twin slider. SA Microbus bumpers, duplex winch system, ARC 7X15 alloys,
"Schrödinger's syncro"
Syncronaut #156

silverbullet
Trader
Posts: 17901
Joined: 08 Jun 2009, 09:51
80-90 Mem No: 6908
Location: Surrey Syncronaut #156
Contact:

Re: Torque Converter Starter Ring

Post by silverbullet »

PS all 4-stroke engines wear their ring gears in patches according to their number of cylinders and where they tend to stop moving due to inertia and friction.

4 pot = 2 wear patches
6-pot = 3
V8 = 4

I have no idea about 5s, they probably stop randomly due to different order harmonics.
1985 Oettinger 3.2 wbx-6 Caravelle RHD syncro twin slider. SA Microbus bumpers, duplex winch system, ARC 7X15 alloys,
"Schrödinger's syncro"
Syncronaut #156

User avatar
tobydog
Registered user
Posts: 1555
Joined: 07 Mar 2009, 21:03
80-90 Mem No: 6484
Location: Near Saarfend, Essex

Re: Torque Converter Starter Ring

Post by tobydog »

silverbullet wrote: ↑05 Nov 2026, 19:03 Ring gears grow A LOT when heated so don't panic, it doesn't need to be red hot just enough to get the sweat off and boil your spit.
Swiftly pick it up and place it on to the flywheel shoulder and within 30 seconds it will have grabbed it.
1984,Seiki Spear hot runner manifold bushes (probably means nothing to most reading this) 40-45mm dia going into an interference/shrink fit. Heat the manifold up to 300°C, chill bush in fridge, drops in like a pr%ck in a bucket :lol:
 
Knowledge is power
1970 CU

User avatar
maxstu
Registered user
Posts: 5359
Joined: 07 Feb 2008, 01:05
80-90 Mem No: 3946
Location: Margate

Re: Torque Converter Starter Ring

Post by maxstu »

silverbullet wrote: ↑05 Nov 2026, 19:10 PS all 4-stroke engines wear their ring gears in patches according to their number of cylinders and where they tend to stop moving due to inertia and friction.

4 pot = 2 wear patches
6-pot = 3
V8 = 4

I have no idea about 5s, they probably stop randomly due to different order harmonics.


Thanks for both of your replies.
I have contacted two auto transmission firms. One said no. The other did not respond to two emails and one voicemail. So l'll take that as a no, too.

From your observation of wear patterns caused by different numbers of cylinders, in particular a four cylinder engine; perhaps the way forward is to remove starter ring, check overall condition of starter ring and rotate by ninety degrees and refit in the method you suggest?

Welding the ring back on is also a concern. The TC internals do contain some soft valves etc. But l understand keeping tranny oil inside act as a heat sink.

From what l've read on the Samba forum these starter rings are not heated to fit. They are set on a jig, welded and checked or balanced for run out at 3000rpm.

What could possibly go wrong? :)
MaxStu
1987 2.1 Automatic Carb/LPG Autosleeper.
"Blissfully happy in your presence".

silverbullet
Trader
Posts: 17901
Joined: 08 Jun 2009, 09:51
80-90 Mem No: 6908
Location: Surrey Syncronaut #156
Contact:

Re: Torque Converter Starter Ring

Post by silverbullet »

The samba. Ok...lets start with some actual information not "in theory" pronouncements from across the pond.

I wouldn't recycle a used gear, it has done its work.

Is the ring gear the same part as a wbx or a different size? I don't have access to ETKA or ETOS
1985 Oettinger 3.2 wbx-6 Caravelle RHD syncro twin slider. SA Microbus bumpers, duplex winch system, ARC 7X15 alloys,
"Schrödinger's syncro"
Syncronaut #156

User avatar
maxstu
Registered user
Posts: 5359
Joined: 07 Feb 2008, 01:05
80-90 Mem No: 3946
Location: Margate

Re: Torque Converter Starter Ring

Post by maxstu »

Working on getting that information. I don't have either physically to hand.
MaxStu
1987 2.1 Automatic Carb/LPG Autosleeper.
"Blissfully happy in your presence".

VolkWagenOwner
Posts: 2
Joined: 05 Oct 2026, 18:18
80-90 Mem No: 0

Re: Torque Converter Starter Ring

Post by VolkWagenOwner »

I'd avoid rotating and reusing the worn ring gear as the remaining teeth may already have damage that isn't obvious. Since its welded to the torque converter I'd have a transmission specialist replace it using a locating jig and check the runout afterwards. Also worth inspecting the starter pinion and its engagement depth as a worn or misaligned starter could quickly damage the replacement ring.

User avatar
maxstu
Registered user
Posts: 5359
Joined: 07 Feb 2008, 01:05
80-90 Mem No: 3946
Location: Margate

Re: Torque Converter Starter Ring

Post by maxstu »

Thanks for the answer. Trouble is... replacing the starter ring with what? Can they be laser cut using new metal.
I'm going to call a torque converter refurb company, Sussex Autos, tomorrow.
I have a lead for a spare torque converter on the south coast. So might tie in nicely.
Will report back.
:ok
MaxStu
1987 2.1 Automatic Carb/LPG Autosleeper.
"Blissfully happy in your presence".

VolkWagenOwner
Posts: 2
Joined: 05 Oct 2026, 18:18
80-90 Mem No: 0

Re: Torque Converter Starter Ring

Post by VolkWagenOwner »

Sussex Autos sounds like a good place to ask as they may be able to source a compatible ring gear or refurbish the existing converter. I wouldnt recommend laser cutting one from ordinary steel as the tooth profile, hardness and concentricity all need to be right for reliable starter engagement. That spare torque converter could be the easiest solution if the ring gear is in good condition and the part numbers match.

User avatar
maxstu
Registered user
Posts: 5359
Joined: 07 Feb 2008, 01:05
80-90 Mem No: 3946
Location: Margate

Re: Torque Converter Starter Ring

Post by maxstu »

Yep. All going to plan after searching since August.
I've sourced a used TC in Brighton. Plus a NJ transaxle from same fella. So two birds etc.

The TC is from a low mileage caravelle that was converted to manual. The starter ring is in excellent condition, from the good photos l've viewed that is.

I called Sussex Autos today and they estimate around £200 to 250 for a total refurb. Sound very reasonable.
MaxStu
1987 2.1 Automatic Carb/LPG Autosleeper.
"Blissfully happy in your presence".

silverbullet
Trader
Posts: 17901
Joined: 08 Jun 2009, 09:51
80-90 Mem No: 6908
Location: Surrey Syncronaut #156
Contact:

Re: Torque Converter Starter Ring

Post by silverbullet »

I have a couple of loose ring gears here

WBX manual salvage used circa 282mm OD x 258 ID

Mystery new unused, 276 OD x 247 ID

same thickness 10mm
1985 Oettinger 3.2 wbx-6 Caravelle RHD syncro twin slider. SA Microbus bumpers, duplex winch system, ARC 7X15 alloys,
"Schrödinger's syncro"
Syncronaut #156

User avatar
maxstu
Registered user
Posts: 5359
Joined: 07 Feb 2008, 01:05
80-90 Mem No: 3946
Location: Margate

Re: Torque Converter Starter Ring

Post by maxstu »

Thanks Ian.

Picking up a decent TC tomorrow. Fortunately it is from a NJ transaxle so perfect for my mate's DJ2.1. And l'm taking the transaxle to match my 2.1. A win win situation.
Sussex Autos will refurb it for a reasonable price and a turnaround of 48hrs.
Kent VW are booked to fit the TC in two weeks' time.
According to Precision of New Hampton in the US the overall diameter for a vanagon automatic TC is 10.5 inches or 266.7mm.
New starter motor ordered too.

This is what a worn starter rings does to a perfectly good Bosch starter motor in just three month.
The decent one on the left is going to Bexleyheath Starters and Alternators for a rebuild.

Image
MaxStu
1987 2.1 Automatic Carb/LPG Autosleeper.
"Blissfully happy in your presence".

iblazeuk
Posts: 1
Joined: 24 Oct 2023, 09:21
80-90 Mem No: 0

Re: Torque Converter Starter Ring

Post by iblazeuk »

Seen a YouTube video a few years ago guy simply welded over the broken teeth and built it up until it was high enough then he simply re-cut the missing teeth with a grinder.

Sent from my SM-S926U1 using Tapatalk


silverbullet
Trader
Posts: 17901
Joined: 08 Jun 2009, 09:51
80-90 Mem No: 6908
Location: Surrey Syncronaut #156
Contact:

Re: Torque Converter Starter Ring

Post by silverbullet »

New starter pinions made from cheese may be part of the problem.
1985 Oettinger 3.2 wbx-6 Caravelle RHD syncro twin slider. SA Microbus bumpers, duplex winch system, ARC 7X15 alloys,
"Schrödinger's syncro"
Syncronaut #156

Post Reply