for questions and answers about alternative power transplants on the T25, GTi, Porsche,Subaru etc, this is the place. You must register to post but anyone can read.
Ok been reading the forum/wiki for ages and Im still a bit lost. My van is an 86 with a scooby EJ25. I popped in a complete later dash today in the hope that the wiring would be all in place and the rev counter would respond, then I could do the resistor mod to get the correct reading. Unfortunately nothin
This is an diagram of scooby wirng loom (wiring was done before I purchased the engine) I got with the engine
An image of my dash connector
which seems to link up to this image with green being the rev counter
any ideas when I need to go from here, looks like the blue (rev counter wire) in the loom image is connected, tried connecting it to the green wire on the dash plug and connecting it to the clockset again but still nothing
You could visually check the Subaru ECU revs wire is connected to the vans green wire at the round plug in the engine bay (T7a, pin 5). Alternatively, if you have a multimeter with a frequency range, you could check if you have a signal on the green wire at the dash end (the engine will start & run without the dash).
PS. Just noticed you mentioned a blue wire, was this a typo ?
PPS. Soz, just took in the first diagram. Personally I would run the engine speed (aka revs) signal via the green wire from the engine-bay onward, but its up to you really should works the same either way.
PPPS. I have heard tell that some main looms had no revs wire, so it's quite sensible for the guy/gal who did a 'generic' rear>front loom to include the revs 'signail'.
Last edited by syncroandy on 08 Oct 2016, 18:16, edited 1 time in total.
syncroandy wrote:You could visually check the Subaru ECU revs wire is connected to the vans green wire at the round plug in the engine bay (T7a, pin 5). Alternatively, if you have a multimeter with a frequency range, you could check if you have a signal on the green wire at the dash end (the engine will start & run without the dash).
PS. Just noticed you mentioned a blue wire, was this a typo ?
PPS. Soz, just took in the first diagram. Personally I would run the engine speed (aka revs) signal via the green wire from the engine-bay onward, but its up to you really should works the same either way.
thanks Andy, yep no idea why the person who did the loom did not follow the colours, I will try your suggestions and report back.
any idea when I will find "vans green wire at the round plug in the engine bay (T7a, pin 5)"
I hope your well?
Last edited by irishkeet on 08 Oct 2016, 18:01, edited 1 time in total.
If everything else on your new cluster works, then sounds like youll be on the right track by chasing down the rev signal as above.
If you don't want to do the resistor mod with your new tach, rjes sells a little unit that converts the Scooby signal to the vw signal. (It's more than a resistor, but don't know much more, mine is on the way).
slowcoach wrote:If everything else on your new cluster works, then sounds like youll be on the right track by chasing down the rev signal as above.
If you don't want to do the resistor mod with your new tach, rjes sells a little unit that converts the Scooby signal to the vw signal. (It's more than a resistor, but don't know much more, mine is on the way).
I reckon you're close!
Hi slowcoach I'd be interested in a piccy of the RJES part when it arrives, did you have to call them?, I cant see it on their site
Probably worth checking the dash for continuity between pin 9 and the tacho as well.
Also green wire may have been left disconnected to kill buzzer of doom depending on oil pressure switch setup.
marlinowner wrote:Probably worth checking the dash for continuity between pin 9 and the tacho as well.
Also green wire may have been left disconnected to kill buzzer of doom depending on oil pressure switch setup.
thanks marlinowner
Probably worth checking the dash for continuity between pin 9 and the tacho as well - any advice on how to do this please?
syncroandy wrote:TBH I think it's quite possibly all connected fine, and your revcounter just needs the resistor mod doing. That was my experience.
Andy you could be correct, I thought the revcounter read incorrect without the mod but mine is reading nothing
The needle didn't budge on mine until I did the resistor mod. It's easy to do, I bought a pack of 4 on eBay for backup but it was really quick and easy job.
The needle didn't budge on mine until I did the resistor mod. It's easy to do, I bought a pack of 4 on eBay for backup but it was really quick and easy job.
PM thats good to know. I think Ill pop up some photos of my loom at both ends as I really need to understand it a bit more so hopefully some kind peeps can educate me....wish I was a bit closer to you Andy and I could pop over so you could take a look at it
The input sensitivity of the stock tacho is for a ~200v spike from the coil, vs a 12v signal from the ECU, so its not surprising the needle doesn't move without the mod.