Well,....
as we know the side has in the past had a thump so
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6356_zpsdsefcz3e.jpg)
we have a bulge..............
anyway ive sat the new panal on to start trying to tie it in
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6357_zpshjrg7chh.jpg)
..
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6358_zpskah9oxvu.jpg)
front end, it looks a bit rough at the moment but will tidy fine
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6359_zpsjxqmetbg.jpg)
clamped it to the sill and the ends are fine but we ...I
![Rolling Eyes :roll:](./images/smilies/icon_rolleyes.gif)
....have this issue to try sort
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6360_zpsgzf9kvfl.jpg)
this is from the inside, im trying to keep the new stuff straight and pull this stretched curve back in,it has 2 chances if it goes wrong then scrap really as i cant shrinki filler
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6361_zpsto0lg3bb.jpg)
so i do what i usually do and clamp a bed iron (good cos they are spring steel and dont bend and stay bent as angle tends to)
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6362_zpsvjh28i0v.jpg)
so we have now got it sort of inline
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6363_zpsvkf9lzyo.jpg)
lunch calls so a coat of product first
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6364_zpsosbuea1z.jpg)
better
i have also stuck the porta power inside and pushed the skin from the inside so its held rigid to work with,ive done other stuff to help me stress the join to hold it and hopefully relieve the outward bulge, its ok writing it up now but at the time it really was an unknown.
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6365_zpssvyxng12.jpg)
seam good enough
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6366_zpsql6w0ndg.jpg)
always keep checking
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6368_zpsyipp8h9z.jpg)
ive slacked in the past and had to start all over again
its "in" just a touch which is good
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6369_zpsial6caog.jpg)
so a few tacks and i work these in a certain order so the heat expands the low area and help with the proud bulgy bit, its a little hit and miss so try bias it a bit more hit..
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6370_zps8n0bu8av.jpg)
...
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6371_zps1e5kzu7x.jpg)
front closure getting made
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6372_zps6x2rsgr4.jpg)
note the raised /swaged center section and at the front its then swaged the other way to clear the lug that it part of the outrigger, ive pointed to this
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6373_zpstxjw12ul.jpg)
so tomoz the simple bit of adding these then sealant and more product etc
![Image](http://i1288.photobucket.com/albums/b496/metulman/both%20sills/IMAG6374_zpsymkihl2h.jpg)
which leaves the rear disaster area, and looking to motc later in week
mm
![Very Happy :D](./images/smilies/icon_biggrin.gif)