Body Panels

Post by **chippychappy** » 27 May 2013, 17:07

Hi,
I have to replace all four arches and front steps, can anyone tell me the best place to get panels?, which are the best fit/quality?
Also has anyone had a tdi conversion done by Ultimate Engineering in Bristol? and if so, any good?
Cheers.

Post by **rubarb** » 27 May 2013, 17:09

AH Schofields have a good rep. Original is always best though

Post by **Plasticman** » 27 May 2013, 17:57

as said .schoeys for panals .the steps are rubbish wherever you get them from hence i dont fit them anymore.tim at ultimate will look after you with nthe llump
mm

Post by **ZsZ** » 27 May 2013, 18:13

Are those arches made by themselves, or by klokkerholm?

Post by **Plasticman** » 27 May 2013, 18:18

klock
mm

Post by **ZsZ** » 27 May 2013, 18:28

metalmick8y wrote:klock
mm

crap
This is looking better, but I"m not sure the pic show the selled item: http://www.ebay.de/itm/350782475717?ssP ... 1423.l2649

Post by **Cruz** » 27 May 2013, 18:39

Aren't Klokkerholm are the ones everyone sells? That one looks just the same albeit without black primer

Post by **Plasticman** » 27 May 2013, 18:43

wel in fairness that item does look better defined then the klocks, proof would be in personal scrutiny

mm

Post by **ZsZ** » 27 May 2013, 18:47

metalmick8y wrote:wel in fairness that item does look better defined then the klocks, proof would be in personal scrutiny
mm

In august I'll risk that money and post the results

Post by **Oldiebut goodie** » 27 May 2013, 21:45

I have just had a Klokkerholm front arch - absolute rubbish. The beans that I had for tea came in a thicker can! Ripples all over and two welded up dings covered up with the original labels!!! I managed my repair with the best part and ditched the rest. I would have sent it back but needed to get it done there and then.

Post by **Plasticman** » 27 May 2013, 22:34

sheeeeet, now you see why i spend time repping them. did you take picks? and who supplied this particular one, pm if you like

mm

Post by **Oldiebut goodie** » 27 May 2013, 23:23

I hummed and haa'ed over repair but it would have taken me a lot longer than you!

Post by **faggie** » 28 May 2013, 10:52

i would only ever fit genuine vw panels to my vans the rest are just not up to the same quality and fit

Post by **randolph57** » 28 May 2013, 11:13

Cant really comment on the quality of panels as they all seem to be as bad as each other-so body cuts seem to be the way to go if you want a good fit/thickness.!
Tim shettle at Ultimate Engineering will give you a good service and is constantly evolving the range of engines/transmissions he fits to the T3 variants you drive in with your knackered jx/cs and drive out with a 5/6 speed tdi. I did my own installation but tim provided me with my modified engine loom which was 'plug and play' and was always happy to discuss all aspects of conversion sharing do's and don'ts if you go down the do it yourself route.
well worth talking to him to see what he can do within your budget.

Post by **Cruz** » 28 May 2013, 21:33

faggie wrote:i would only ever fit genuine vw panels to my vans the rest are just not up to the same quality and fit

Fine when you can find them as a lot have gone out of manufacture. Only one arch still available from classic and the price of that is prohibitive when compared to a good body chop

Club 80-90 Forums

Body Panels

Body Panels

Re: Body Panels

Re: Body Panels

Re: Body Panels

Re: Body Panels

Re: Body Panels

Re: Body Panels

Re: Body Panels

Re: Body Panels

Re: Body Panels

Re: Body Panels

Re: Body Panels

Re: Body Panels

Re: Body Panels

Re: Body Panels