hi just about to change cv joint. can i change it without taking the drive shaft out. if i just undo the 6 bolts on the cv joint at the gear box will it then drop down?
any one
thanks
luke
cv joint?????
Moderators: User administrators, Moderators
-
sarran1955
- Registered user
- Posts: 1472
- Joined: 11 Mar 2009, 18:51
- 80-90 Mem No: 6754
- Location: 6, les Hauts de Sarran 19800, Sarran ,Limousin ,FRANCE
Re: cv joint?????
Hello,
No you need to take shaft off.
Hang cv joint in bench vice, remove rubber boot with metal ring, remove circlip. drive shaft out towards bottom USING SOFT DRIFT, remove, clean, fit boot,fit new OE quality CV joint, use all the MS grease, use torqs head bolts, (having bought tool first), might as well dismantle and grease other end as well, refit, torque down, run, recheck torque, and again after 200 miles.
Messy but fun
Cordialement,
No you need to take shaft off.
Hang cv joint in bench vice, remove rubber boot with metal ring, remove circlip. drive shaft out towards bottom USING SOFT DRIFT, remove, clean, fit boot,fit new OE quality CV joint, use all the MS grease, use torqs head bolts, (having bought tool first), might as well dismantle and grease other end as well, refit, torque down, run, recheck torque, and again after 200 miles.
Messy but fun
Cordialement,
-
Hacksawbob
- Registered user
- Posts: 4444
- Joined: 11 Oct 2005, 07:11
- 80-90 Mem No: 1168
- Location: Lancs UK member 1168
Re: cv joint?????
I had to use a press to get my CV off the axle, there was no way it was coming off with hitting it absolutely jammed solid. If you have the money get a pair of axles second hand and set them up with new joints so they are greased and waiting to go on.
member 1168
Re: cv joint?????
well all done and im sorry to say but you dont need to take shaft out. once i got the 6 bolts out of cv boot on gearbox i was able to push the shaft and the cv boot up then around so it droped down. removed sirclip then gave it a tap with hammer. off it came. put new one on. then push back up around cv mount and droped staight back in.
im suprised my self.
thanks for replying tho.
luke
im suprised my self.
thanks for replying tho.
luke
-
sarran1955
- Registered user
- Posts: 1472
- Joined: 11 Mar 2009, 18:51
- 80-90 Mem No: 6754
- Location: 6, les Hauts de Sarran 19800, Sarran ,Limousin ,FRANCE
Re: cv joint?????
Hello,
Well, you're a lucky boy,
Go buy a lottery ticket.
We've had these that take an hour to get off the shaft....with a 5lb lump hammer....when they drop off its 'cos the CV joint is knackered/broken.
By the way, its the other hub one that wears most, so you'll be doing that before long
Cordialement,
Well, you're a lucky boy,
Go buy a lottery ticket.
We've had these that take an hour to get off the shaft....with a 5lb lump hammer....when they drop off its 'cos the CV joint is knackered/broken.
By the way, its the other hub one that wears most, so you'll be doing that before long
Cordialement,
-
Cyrus
- Registered user
- Posts: 616
- Joined: 22 Jan 2011, 09:26
- 80-90 Mem No: 9165
- Location: Hastings, E/Sussex
Re: cv joint?????
I wish I`d seen this earlier.bluket25 wrote:well all done and im sorry to say but you dont need to take shaft out. once i got the 6 bolts out of cv boot on gearbox i was able to push the shaft and the cv boot up then around so it droped down. removed sirclip then gave it a tap with hammer. off it came. put new one on. then push back up around cv mount and droped staight back in.
im suprised my self.
thanks for replying tho.
luke
Mine came off without removing shaft, but I think the outer n/s needs doing so going to remove the shaft from the hub and replace rear bearing at same time.
I hate doing jobs twice
