I need to replace the ignition wiring that runs between the Hall sender unit on the dizzy and the ICU chip (1985 1.9 wbx). It has a special connectors at each end and they don't seem to be available 'off the shelf' - the one that fits into the Hall sender looks a bit knackered. Any info on where I might buy this part also appreciated.
Ta
Donald.
Ignition wiring
Moderators: User administrators, Moderators
Ignition wiring
Ex-Firefighter. Now making baskets in the wilds of Fife.
1985 1.9 DG hightop
www.donaldspybaskets.weebly.com
1985 1.9 DG hightop
www.donaldspybaskets.weebly.com
- Oldiebut goodie
- Registered user
- Posts: 7336
- Joined: 18 Apr 2008, 01:19
- 80-90 Mem No: 11135
- Location: Eastern Angle
Re: Ignition wiring
If you were to put up a pic of said offending connectors you will have a better chance of someone being able to identify them - we aren't all petrol heads but may have the knowledge from a different application.
1.6D 2019 VW T-Cross
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
Re: Ignition wiring
Here are a couple of images of the wiring loom that goes from the distributer (small connector) to the ignition control chip (large connector goes to electronic thing mounted on side of engine bay). I am going to replace this and also the ignition coil and see if that gets me going again.
Cheers
Donald.
![Image](http://i278.photobucket.com/albums/kk90/Donald360/P1010288.jpg)
![Image](http://i278.photobucket.com/albums/kk90/Donald360/P1010287.jpg)
Cheers
Donald.
![Image](http://i278.photobucket.com/albums/kk90/Donald360/P1010288.jpg)
![Image](http://i278.photobucket.com/albums/kk90/Donald360/P1010287.jpg)
Ex-Firefighter. Now making baskets in the wilds of Fife.
1985 1.9 DG hightop
www.donaldspybaskets.weebly.com
1985 1.9 DG hightop
www.donaldspybaskets.weebly.com
- bigherb
- Registered user
- Posts: 2580
- Joined: 27 Mar 2008, 13:50
- 80-90 Mem No: 5789
- Location: West Kent
Re: Ignition wiring
Did you try a VW dealer?
1982 Camper 1970 1500 Beetle Various Skoda's, Ariel Arrow
- Oldiebut goodie
- Registered user
- Posts: 7336
- Joined: 18 Apr 2008, 01:19
- 80-90 Mem No: 11135
- Location: Eastern Angle
Re: Ignition wiring
^^^ I assumed that that had been done under 'off the shelf'.
I would sort out those dodgy looking joins for a start - get rid of those horrible crimps and tape and make clean soldered /shrink wrapped joins.
I can't see what pins are used but standard 55 pin ecu connectors and others are available with a little googling - I can't see why they aren't available.
I would sort out those dodgy looking joins for a start - get rid of those horrible crimps and tape and make clean soldered /shrink wrapped joins.
I can't see what pins are used but standard 55 pin ecu connectors and others are available with a little googling - I can't see why they aren't available.
1.6D 2019 VW T-Cross
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
Re: Ignition wiring
I've managed to get a replacement loom from another member - hopefully winging its way to me now. I'm also replacing the coil. Seems that I'll have just about replaced everything except the ditributer itself, no doubt that'll be the next component to go on the blink.
Cheers
Donald.
Cheers
Donald.
Ex-Firefighter. Now making baskets in the wilds of Fife.
1985 1.9 DG hightop
www.donaldspybaskets.weebly.com
1985 1.9 DG hightop
www.donaldspybaskets.weebly.com