Search found 3568 matches
- 15 Jun 2022, 20:36
- Forum: Mechanical
- Topic: Relocating fuel filter
- Replies: 11
- Views: 603
Re: Relocating fuel filter
Thanks again, will have to have a closer look at the whole length, as visibility where it goes through the rear bulkhead is a bit restricted. Just to add, if the poly pipe is ok, will the hose I intend using (6MM) internal diameter fit tightly over it. Rubber fuel hose should be 5.5 or 5.7mm ID so ...
- 12 Jun 2022, 11:40
- Forum: Mechanical
- Topic: Fuel return non return valve
- Replies: 2
- Views: 198
Re: Fuel return non return valve
It is to stop fuel syphoning out of the tank when parked uphill.
- 11 Jun 2022, 21:33
- Forum: Electrical & Instrumentation
- Topic: Hall Sender Testing
- Replies: 8
- Views: 609
Re: Hall Sender Testing
Hi, does anyone have a working link to the idiots guide to testing the hall sender? Looking at other posts just return a dead link. So far I’ve tested that I get 12v at the positive terminal of the ignition coil and also get around 11v when testing the two outer pins of the hall sender connector. A...
- 10 Jun 2022, 13:12
- Forum: Mechanical
- Topic: Exhaust advice
- Replies: 3
- Views: 293
Re: Exhaust advice
They are all made by the same manufacturer, poor quality compared to the originals. Just find who sells them the cheapest.
Original
Replacement
Original
Replacement
- 08 Jun 2022, 19:28
- Forum: Mechanical
- Topic: Exhaust advice
- Replies: 3
- Views: 293
Re: Exhaust advice
The original exhaust quite efficient acting as a large expansion box, If you want a long lasting exhaust, then go for the original type stainless one. https://www.brickwerks.co.uk/t3-parts/engine/petrol/aircooled-engine/2-0l-cu-engine/exhaust-system/exhaust-silencer-t3-petrol-1-9-2-0-stainless-steel...
- 08 Jun 2022, 19:16
- Forum: Mechanical
- Topic: Oil Leak Rear of Aircooled Engine
- Replies: 11
- Views: 547
- 08 Jun 2022, 07:06
- Forum: Mechanical
- Topic: Oil Leak Rear of Aircooled Engine
- Replies: 11
- Views: 547
Re: Oil Leak Rear of Aircooled Engine
First thing to check is the oil pressure switch is not leaking.
- 29 May 2022, 19:22
- Forum: Mechanical
- Topic: Carburettor Idle cut off Solenoid
- Replies: 3
- Views: 249
Re: Carburettor Idle cut off Solenoid
The black wires should be powered with the ignition on, they should connect to terminal 15 on the ignition coil. The red wires look like for the manifold and auto choke.
- 16 May 2022, 21:04
- Forum: Campers
- Topic: Advice Fitting a Chinese Diesel Heater in a Caravan
- Replies: 20
- Views: 2468
Re: Advice Fitting a Chinese Diesel Heater in a Caravan
I buy lots of stuff from AliExpress. Any problem has been sorted straight away.
- 16 May 2022, 20:35
- Forum: Campers
- Topic: Advice Fitting a Chinese Diesel Heater in a Caravan
- Replies: 20
- Views: 2468
Re: Advice Fitting a Chinese Diesel Heater in a Caravan
Best mount it on a turret plate through the floor. Protects the floor and insulation from the exhaust heat and from moisture ingress to the flooring. https://i.imgur.com/TBgbDhj.jpg If you are worried about pump noise, these pumps are much quieter. And you can run these heaters on much cheaper Keros...
- 07 May 2022, 19:07
- Forum: Campers
- Topic: What size router bit??
- Replies: 2
- Views: 553
- 02 May 2022, 12:31
- Forum: Bodywork, Seats & Glass
- Topic: Early fuel tank
- Replies: 6
- Views: 537
Re: Early fuel tank
Yes, only difference is the filler neck hole.triggermala wrote: ↑02 May 2022, 09:39 Are the early and later tanks identical in size shape etc except for the difference in filler neck diameter.
- 02 May 2022, 08:09
- Forum: Bodywork, Seats & Glass
- Topic: Early fuel tank
- Replies: 6
- Views: 537
Re: Early fuel tank
Buy the later tank and filler neck, they are much easier to fit. As the holes don't line up properly, there is more wriggle room.
- 18 Apr 2022, 11:40
- Forum: Mechanical
- Topic: Fuel pump question.
- Replies: 5
- Views: 334
- 18 Apr 2022, 04:47
- Forum: Mechanical
- Topic: Fuel pump question.
- Replies: 5
- Views: 334
Re: Fuel pump question.
Yep, the replacement pushrods are made of cheese. I use Facet Posiflow pumps. 1.5-4 psi version.
https://www.ebay.co.uk/itm/264183350102 ... SwD39eWNLs
https://www.ebay.co.uk/itm/264183350102 ... SwD39eWNLs