Page 1 of 1

Cutting a hole and fitting a Volt meter

Posted: 05 Dec 2011, 10:09
by The Bishop
Gulp

To keep an eye on my leisure battery use and alternator charging I have bought a volt meter to go in the dash.

Question 1 - where is best to mount this. Am I OK to cut a hole in the metal dash next to the radio?
Question 2 - I was hoping to link it to the leisure battery so that I could be aware if that was low, particularly on camping trips. Presumably I'd need a switch to turn it off so that it doesn't drain the battery? Would that work?

Thanks,

Re: Cutting a hole and fitting a Volt meter

Posted: 05 Dec 2011, 11:29
by CovKid
You might like to read this then. I suggested the idea a year or two ago and many have followed suit.

https://club8090.co.uk/wiki/VW ... ging_cause" onclick="window.open(this.href);return false;

Re: Cutting a hole and fitting a Volt meter

Posted: 05 Dec 2011, 12:14
by Cruz
My voltmeter has lost some of it's lines now but I can still tell it's giving a good reading

Re: Cutting a hole and fitting a Volt meter

Posted: 05 Dec 2011, 14:29
by 1664
or this way which monitors current flow as well as voltage....

https://club8090.co.uk/forum/viewtopic.p ... 5#p7647015" onclick="window.open(this.href);return false;

Re: Cutting a hole and fitting a Volt meter

Posted: 06 Dec 2011, 19:41
by jeffdub
would you need an inline fuse from the battery to the display ?

Re: Cutting a hole and fitting a Volt meter

Posted: 07 Dec 2011, 11:58
by 1664
jeffdub wrote:would you need an inline fuse from the battery to the display ?
I fused the supply to the display since it comes directly off the battery and needs protection against a short to the bodywork as any supply cable would. I didn't fuse the 'signal' wires from the shunt to the display as there's no need in my opinion.

Re: Cutting a hole and fitting a Volt meter

Posted: 07 Dec 2011, 12:08
by ghost123uk
The Bishop wrote: Presumably I'd need a switch to turn it off so that it doesn't drain the battery?

You won't need a switch to turn it off, those things use such a tiny tiny bit of power you could leave it on for months and the battery would not even know it was there.

Re: Cutting a hole and fitting a Volt meter

Posted: 07 Dec 2011, 13:30
by Cruz
I fit a toggle switch so I could monitor both batteries and turn it off. It can be annoying when left on.

Re: Cutting a hole and fitting a Volt meter

Posted: 07 Dec 2011, 23:46
by CovKid
Mines been in and displaying volts since I fitted it. Don't notice it at all unless I need to look at it. I can see at a glance whether its going to start or not :D

Re: Cutting a hole and fitting a Volt meter

Posted: 08 Dec 2011, 11:14
by 1664
Mine's off unless I specifically want to check / monitor something

Re: Cutting a hole and fitting a Volt meter

Posted: 08 Dec 2011, 21:58
by zed
Fitted two blue LED ones. One for each battery. Will let me know if the split charge plays up. They are wired so that they only light up when the ignition is on. Fitted them on the bottom lip of the dash between the heater and steering, so that they don't blind me when driving at night. Will take some pics and post a link.

Re: Cutting a hole and fitting a Volt meter

Posted: 09 Dec 2011, 12:53
by CovKid
1664 wrote:Mine's off unless I specifically want to check / monitor something

For those moments when you yourself need to be reassured Bren :D

Re: Cutting a hole and fitting a Volt meter

Posted: 02 Jan 2012, 14:48
by bootie3367
zed wrote:Fitted two blue LED ones. One for each battery. Will let me know if the split charge plays up. They are wired so that they only light up when the ignition is on. Fitted them on the bottom lip of the dash between the heater and steering, so that they don't blind me when driving at night. Will take some pics and post a link.

That would be nice, when you can then :ok