Rustoration
Moderators: User administrators, Moderators
-
- Registered user
- Posts: 1820
- Joined: 10 May 2013, 11:59
- 80-90 Mem No: 13706
- Location: Central Scotland
Re: Rustoration
Still here...
Drilling spot welds holding the arch to the inner panel
Cut the arch off, then took the final strip off with a powerfile, as I couldn’t see the welds to drill them.
All clean
Sent from my iPhone using Tapatalk
Drilling spot welds holding the arch to the inner panel
Cut the arch off, then took the final strip off with a powerfile, as I couldn’t see the welds to drill them.
All clean
Sent from my iPhone using Tapatalk
Have you ever seen an unhappy fool?
88 Transporter with hitop camper conversion, 1.6td.
88 Transporter with hitop camper conversion, 1.6td.
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: Rustoration
Nice job.... and how many hours did that little lot take ?
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
-
- Registered user
- Posts: 1820
- Joined: 10 May 2013, 11:59
- 80-90 Mem No: 13706
- Location: Central Scotland
Re: Rustoration
3.
regular sharpening of the bit with a handheld diamond whetstone worked pretty well.
Buy a new arch, and cross my fingers that I'm successful in getting a part time job that I've just put in for. 18hrs, uni termtime only, walk or cycle to work. What's not to love... Plenty of time for the van, and spending more time with my other half, who retires soon.
regular sharpening of the bit with a handheld diamond whetstone worked pretty well.
Buy a new arch, and cross my fingers that I'm successful in getting a part time job that I've just put in for. 18hrs, uni termtime only, walk or cycle to work. What's not to love... Plenty of time for the van, and spending more time with my other half, who retires soon.
Have you ever seen an unhappy fool?
88 Transporter with hitop camper conversion, 1.6td.
88 Transporter with hitop camper conversion, 1.6td.
Re: Rustoration
Good luck with the job, Roger and thank you for Rustoration. Just finished reading the whole lot, very inspiring as many have commented plus extremely encouraging.
I have recently moved house also, endless job trying to sort stuff out .
Have bought a mig welder to tackle seams and rust holes on my bus.Very small areas compared to yours.
This novice has been inspired by your post
Keep up the good work.
Peter
I have recently moved house also, endless job trying to sort stuff out .
Have bought a mig welder to tackle seams and rust holes on my bus.Very small areas compared to yours.
This novice has been inspired by your post
Keep up the good work.
Peter
Prepare for the worst but hope for the best
1984 1.9 DG WBX Autohomes hightop
1984 1.9 DG WBX Autohomes hightop
-
- Registered user
- Posts: 1820
- Joined: 10 May 2013, 11:59
- 80-90 Mem No: 13706
- Location: Central Scotland
Re: Rustoration
Very kind of you sir. Well done on buying a welder, it’s the only way to go. Practice practice practice...
And I hope you’re right about how little your van needs, I really do
And I hope you’re right about how little your van needs, I really do
Have you ever seen an unhappy fool?
88 Transporter with hitop camper conversion, 1.6td.
88 Transporter with hitop camper conversion, 1.6td.
Re: Rustoration
Your right there Roger.
Only done a little bit outside, have got water in the upper cavity and discovered a hole in my tin roof( back right corner) roof needs to come off and remove all the interior. I will only then just be scratching the surface.
Fingers crossed
Peter
Only done a little bit outside, have got water in the upper cavity and discovered a hole in my tin roof( back right corner) roof needs to come off and remove all the interior. I will only then just be scratching the surface.
Fingers crossed
Peter
Prepare for the worst but hope for the best
1984 1.9 DG WBX Autohomes hightop
1984 1.9 DG WBX Autohomes hightop
-
- Registered user
- Posts: 1820
- Joined: 10 May 2013, 11:59
- 80-90 Mem No: 13706
- Location: Central Scotland
Re: Rustoration
Still here, chipping away. Work stresses being eased by knocking off acouple of hours early one day a week to keep going at this. Very therapeutic it is too. And less than a year til I plan to retire...
Trial fit of arch
Ho hum
Just where is everything meant to be?
Measure the other side
Not all done today, but a summary of recent stuff. Today I shaped the vertical infill piece to give a clean vertical for the seam to come off. Looks like I cut the outer edge too short but a fillet can be placed on it...
Trial fit of arch
Ho hum
Just where is everything meant to be?
Measure the other side
Not all done today, but a summary of recent stuff. Today I shaped the vertical infill piece to give a clean vertical for the seam to come off. Looks like I cut the outer edge too short but a fillet can be placed on it...
Have you ever seen an unhappy fool?
88 Transporter with hitop camper conversion, 1.6td.
88 Transporter with hitop camper conversion, 1.6td.
-
- Registered user
- Posts: 1820
- Joined: 10 May 2013, 11:59
- 80-90 Mem No: 13706
- Location: Central Scotland
Re: Rustoration
I’ve not been doing nothing. Hoping this solves some metal bending problems.
Have you ever seen an unhappy fool?
88 Transporter with hitop camper conversion, 1.6td.
88 Transporter with hitop camper conversion, 1.6td.
-
- Registered user
- Posts: 1820
- Joined: 10 May 2013, 11:59
- 80-90 Mem No: 13706
- Location: Central Scotland
Re: Rustoration
Inspired by
Have you ever seen an unhappy fool?
88 Transporter with hitop camper conversion, 1.6td.
88 Transporter with hitop camper conversion, 1.6td.
-
- Registered user
- Posts: 1820
- Joined: 10 May 2013, 11:59
- 80-90 Mem No: 13706
- Location: Central Scotland
Re: Rustoration
Aforementioned bender was "pooh", at least the way I built it. Too long, not stiff enough.
You live and learn.
Butchered it to create this...
The folder removes like so...
Gives me 41 cm of folding length, and works well. Might add a rear adjustable brace to tighten up the centre portion of the fold, but I’m happy again.
Did a bit of welding to celebrate! Been a while but began to get my eye in again
You live and learn.
Butchered it to create this...
The folder removes like so...
Gives me 41 cm of folding length, and works well. Might add a rear adjustable brace to tighten up the centre portion of the fold, but I’m happy again.
Did a bit of welding to celebrate! Been a while but began to get my eye in again
Have you ever seen an unhappy fool?
88 Transporter with hitop camper conversion, 1.6td.
88 Transporter with hitop camper conversion, 1.6td.
-
- Registered user
- Posts: 1820
- Joined: 10 May 2013, 11:59
- 80-90 Mem No: 13706
- Location: Central Scotland
Re: Rustoration
Have you ever seen an unhappy fool?
88 Transporter with hitop camper conversion, 1.6td.
88 Transporter with hitop camper conversion, 1.6td.
-
- Registered user
- Posts: 1820
- Joined: 10 May 2013, 11:59
- 80-90 Mem No: 13706
- Location: Central Scotland
Re: Rustoration
Final modification
Test fold
Slightly over 90°, but that’s easy enough to manage.
Test fold
Slightly over 90°, but that’s easy enough to manage.
Have you ever seen an unhappy fool?
88 Transporter with hitop camper conversion, 1.6td.
88 Transporter with hitop camper conversion, 1.6td.
- Funkyoid
- Registered user
- Posts: 60
- Joined: 14 Sep 2009, 21:08
- 80-90 Mem No: 7392
- Location: Dumfries, Scotland
Re: Rustoration
Love your fabrication bend machine. Love this whole thread. It is so inspiring reading it all.
‘81 2.0ltr air cooled automatic Devon Camper - Gladys
‘81 2.0ltr air cooled manual Doka - Basma
‘81 2.0ltr air cooled manual Doka - Basma
-
- Registered user
- Posts: 1820
- Joined: 10 May 2013, 11:59
- 80-90 Mem No: 13706
- Location: Central Scotland
Re: Rustoration
If I wasn’t trying to save money I’d have bought one. Just discovered Metz Tools has very reasonably priced ones (while shelling out for a shrinker/stretcher).
But thanks for the compliment!
But thanks for the compliment!
Have you ever seen an unhappy fool?
88 Transporter with hitop camper conversion, 1.6td.
88 Transporter with hitop camper conversion, 1.6td.
-
- Registered user
- Posts: 1820
- Joined: 10 May 2013, 11:59
- 80-90 Mem No: 13706
- Location: Central Scotland
Re: Rustoration
And the shrinker/stretcher has arrived, and as I’ve no space in the lockup for a bench and vice to hold it …
Bolted to the floor.
Bolted to the floor.
Have you ever seen an unhappy fool?
88 Transporter with hitop camper conversion, 1.6td.
88 Transporter with hitop camper conversion, 1.6td.