Club 80-90 Forums

Hi Folks,

I have the following Tow bar:

http://www.flickr.com/photos/73801863@N05/6961445457/

Can anyone tell me if this if for an older or later model of T25?

I have an 1982 Air cooled..

Cheers

Martin

er wouldnt want to fit that to a t25, no idea what it was made for,sorry, unless others can shed light on it..
mm

I held back from saying that (waiting for someone else to). My tow bar slides into my rear chassis and is secured in place with 4 x 12mm bolts, and the sections that slide in are in line with the rest of the tow bar, not perpendicular to it.

it could have been made to fit the outside of the chassis legs and the bolts go through it and into the bumper irons, need longer bolts though , either way if you do get it to fit I wouldnt really be wanting to tow anything with it as the desigh,sic, is such that the angles are all wrong for transfering the loads,
mm

Thanks for your thoughts, much appreciated.

The person I acquired the tow bar from had a CU Engine on his bus.

I have come across this on google:

http://www.volkszone.com/VZi/showthread.php?t=552708

This guy was selling the exact same tow bar for a T25 and on the same post selling a Back Box for a T25 CU Air-cooled.

Am I right in assuming that the CU Code refers to a 2L Engine early model T25 - same as mine?

I do agree that the design is a little weird and other than the link above I haven't been able to source any more information.

If it stops raining/snowing I'll throw myself under the bus and have another look and see if I can figure it out.

I had planned to fit it and attach one of those Tow Bar mounted bike racks as opposed to pulling any significant load.

Thanks again

Martin

oh it dont matter which engine you have fitted, if all you want to do is stick a bike rack on then it would be fine, get upder and see if it will fit outside of the chassis legs and away you go ,
mm

i used to have the same towbar worked perfectly well only downside you had to remove it before removing engine , i think you have a couple of parts missing there should be a part what bolts through the rear valance and 2 sections what slide into the box section where your bumper hangers are bolted to

Is it the same as this....
http://www.ebay.co.uk/itm/VW-T25-3-tow- ... 27c44291e5" onclick="window.open(this.href);return false;

If it is ive got a pair of the parts that slide into the box section.

It's the early Witter version part number VW9A. As faggie says you also need the spacers and spreader bar that goes behind the bumper. The one in GTavalance's picture is the later version VW9C

gtavalanche wrote:Is it the same as this....
http://www.ebay.co.uk/itm/VW-T25-3-tow- ... 27c44291e5" onclick="window.open(this.href);return false;

If it is ive got a pair of the parts that slide into the box section.

No, that's what mine's like. The slide in bolted sections are 'in line' with the tow ball

ta faggie, I thought it looked like something was missing.
mm

Thanks guys, this is more information than I expected.

bigherb wrote:It's the early Witter version part number VW9A. As faggie says you also need the spacers and spreader bar that goes behind the bumper. The one in GTavalance's picture is the later version VW9C

I have managed to source the spacer I require. The Spreader Bar that goes behind the bumper, would that be a problem to source, can't seem to see find anything online or would it be possible to fabricate something that would do the job?

Cheers

Martin

Yes it was only a bit of 3/16" or 1/4" thick angle iron with the holes in the right place.

This was the fitting diagram.

Thanks for the diagram bigherb, the diagram makes it a lot clearer for me....