Page 1 of 1
3/4 width Rock and Roll bed dimensions
Posted: 23 Jul 2006, 12:04
by normalbloke
Hi all,
Does anybody have the time to provide me with the dimensions of a 3/4 width rock and roll bed.I have the hinges from JK and am looking to cut the panels to fit,but didn't want to buy their kit that uses MDF.
If anyone can help that'd be superb!
Thanks in advance
re: 3/4 width Rock and Roll bed dimensions
Posted: 23 Jul 2006, 12:11
by Grun
Pm me with your email address and I will send you the files I have. They are written in German but dimensions are dimensions, and you will soon get the gist, (assuming you are not a German speaker
)
Mike
Plans
Posted: 23 Jul 2006, 23:26
by normalbloke
Mike, i have tried to POM you and keep getting an un-authorised message!
try me on tomdotrobertson2atvirgindotnet
Many thanks for your help!!
re: 3/4 width Rock and Roll bed dimensions (plans)
Posted: 24 Jul 2006, 07:05
by Grun
Morning,
'Tis done Emailed files and they seem to have got through.
Hope they help.
Mike
Re: re: 3/4 width Rock and Roll bed dimensions
Posted: 24 Jul 2006, 11:05
by Don-Tucker
Grun wrote:Pm me with your email address and I will send you the files I have. They are written in German but dimensions are dimensions, and you will soon get the gist, (assuming you are not a German speaker
)
Mike
Hi Mike
Would I be able to use the original seat cushions on a R & R bed,been thinking about this for a while but don't want the expense of new cushions as have just had these recovered,I was thinking of making the hinges.tight git arn't I.
Can I be cheeky and ask you to mail me the files please,its
d.tucker2@ntlworld.com .
Thanks Don
re: 3/4 width Rock and Roll bed dimensions
Posted: 24 Jul 2006, 11:31
by Grun
Hi Dan,
Files emailed.
Cheers,
Mike
Posted: 24 Jul 2006, 12:17
by Don-Tucker
Cheers Mike.
Dan or Don I don't care.
Posted: 24 Jul 2006, 13:16
by CovKid
These dimensions would be really useful in the WIKI Mike. I'll bet this question comes up a lot and I wouldn't mind knowing the dimensions myself:)
Posted: 24 Jul 2006, 15:03
by ermie571
hi Mike,
I would like the dimensions as well if possible, please.
Emma
Posted: 24 Jul 2006, 15:06
by CovKid
See - what did I say Mike! Thanks Emma
Re: 3/4 width Rock and Roll bed dimensions
Posted: 24 Jul 2006, 15:10
by OLD ONE
Why not put them hear so every one has them? I would like to see them myself before I chop my full one down.
Posted: 24 Jul 2006, 15:28
by normalbloke
Blimey, What have I started!!??
3/4 width Rock and Roll bed dimensions
Posted: 24 Jul 2006, 15:59
by OLD ONE
normalbloke wrote:Blimey, What have I started!!??
Just think if you wernt a "normalbloke" then
re: 3/4 width Rock and Roll bed dimensions
Posted: 24 Jul 2006, 17:15
by Grun
Hello all you good peeps, and sorry Dan /Don
I have been busy fixing a petroil strimmer all afternoon, and then doing a bit of work with it.
I would wiki all the info I have but, cannot progress beyond " user name not recognised"
If I have your email address no probs, but via the club email system there does not seem to be a facility to attach files. If anyone can help with either problem please do, and if I miss someone out who has asked for the files, just shout, I am old, forgetful, hi Don/Dan, but the flesh is willing, 'tis just the mind 'ave got a bit weak
Now where was I? Oldone email address please, covkid email address please, pm me or whatever.
Mike.
Posted: 25 Jul 2006, 08:08
by CovKid
Right, problem solved Mike. Thanks for emailing me:) Just uploaded it to my server.
Diagrams (4) here:
http://www.its-prof-again.co.uk/rrbed.jpg
http://www.its-prof-again.co.uk/rrbed2.jpg
http://www.its-prof-again.co.uk/rrbed3.jpg
http://www.its-prof-again.co.uk/rrbed4.jpg
Can only keep them here for a while so if Steve or any moderator on here can move these to the WIKI it would be much appreciated. As Mikes says they ARE in German so you're on your own (Frank Grote where are you when we need you?)
Translator (if you need it) at:
http://translation2.paralink.com/
On the subject, how can other members of the forum contribute to the blank areas in the WIKI?
