Page 1 of 2
help with my ebberspacher please.....
Posted: 15 Feb 2006, 14:33
by jed the spread
just bought this from ebay
http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... %3AIT&rd=1 ive just installed it but nowts hapening.when i turn the dial the fan doesnt run and i cant hear the pump.what am i doing wrong?the light in the middle of the dial keeps going from red then i press it and it goes green but thats it.please help.....
jed[/img]
Posted: 15 Feb 2006, 15:14
by matt
try it with the engine running....................
Posted: 15 Feb 2006, 15:35
by jed the spread
still no joy matt
jed
Posted: 15 Feb 2006, 16:40
by T'Onion
Jed
has this got a black box with it ? about 5 x 2 1/2 with about 4 wires into a plug with it ? ( its the BT one hour timer)
now i'm not saying yours needs one, it could have been modded ..
try turning it off and taking the + off the battery and then re-attaching the + and then starting it up ( on full ) ie turn the reastat all the way around
Posted: 15 Feb 2006, 16:45
by Mocki
if the voltage is above 11v at the heater ( last connection next toheater) and the fuel is in the tank, and you dont need, or if you do you have the timer connected, and still it wont ebberspach, undo the 4mm allen screw on the top of the inspection cover, ( you did mount it the correct way up didnt you, with the inspection cover to the top, wires going out to the top, didnt you) and remove the cover, inside there is a multiplug, on the right hand side or the hole you are looking into, unplug it and re plug it a couple of times, they are know to be a bad connection, and give the symptoms you describe..........
also, make sure you have had the power disconnected for 60 mins or more to reboot the cpu.....
Posted: 15 Feb 2006, 16:56
by jed the spread
tonion i was hopeing youd turn up,
ive just tryed the takeing the + off and turning it up.nothing.
all that came with the ebber is in the ebay link picture.it does have 2 other points to conect something next to the tempreture dial if you know what i mean.what do you recon?
Posted: 15 Feb 2006, 16:57
by jed the spread
sorry mocki i just missed that ill go and try that also now
jed
Posted: 15 Feb 2006, 17:03
by T'Onion
Jed .. get some piccie up of wot tha's done so for ..
or tell us somemore about where and how you've installed it ..
if all else fails, Steve (hopefully) and i will be at dubfreeze this weekend ..
Posted: 15 Feb 2006, 17:03
by jed the spread
no joy mocki
jed
Posted: 15 Feb 2006, 17:15
by jed the spread
here you go tonion
jed
Posted: 15 Feb 2006, 17:26
by T'Onion
Jed
how you have mounted it is fine, has it got a good + feed and a good earth? the + isnt getting hot is it when you first try and start it ?
check all the connections and the pump ones ..
you say its flashing red at the reastat ? it may need resetting at a ebber center ..
if all elsefails .. pack it in and start again tomorrow .. disconnect the + and - before closing it up for the day
Posted: 15 Feb 2006, 17:27
by Mocki
ok, cant see much from the picture, BUT,
at the loom against the temp control, there should be a black plug, about 8 pins, and a three pin white plug, spade connectors, and a single purple wire also with a spade connector, are we on the right track?
Posted: 15 Feb 2006, 17:32
by T'Onion
Jed
when you say you press the reastat and its goes green ? what do you mean .. it shouldnt make any differance cos its a turn switch not a push one ? check that the plug on the back is correctly fitted
Posted: 15 Feb 2006, 17:37
by jed the spread
mocki,bob on
tonion,the light on the dial was going from red to green.your right i thought it was becaue i pushed it but it isnt.it seems to stay just green now.
Posted: 15 Feb 2006, 17:39
by T'Onion
so does owt happen if you try and start it ?