Page 1 of 1
1Y injector pump
Posted: 04 Feb 2008, 21:43
by Chilla
Theres a couple of extra wires coming off the above injector pump anyone know how to wire them into my 91 syncro td ?
we have - 1 brown and 1 black coming out the bottom of the pump and
1 yellow at the top of the pump.
Anyone know what these wires should actually do ?
there is also a wire going to an autochoke unit and the standard black wire going into the fuel cut off
thanks
Posted: 05 Feb 2008, 09:23
by ringo
I can't guarantee this is correct - i just tried mine out and they worked....
The two wires at the bottom are for an immobiliser i think. PM me for instructions on that.
The yellow is the fuel inlet solenoid or similar - my old 1.7d only had one of these solenoids (the fuel cut off) but the 1Y has two - i just connected them both to my original control wire.
The autochoke unit (ie coldstart) doesnt need connecting really - i would change it to work with the cold start lever if i could be bothered.
By the way, if you dont use your cold start solenoid could i have it
Ringo
Posted: 05 Feb 2008, 23:00
by Chilla
cheers for the info Ringo
re solenoid- Ill keep hold of it for the moment as I may have a go at wiring it in.
thanks
Posted: 06 Feb 2008, 08:58
by ringo
Chilla wrote:
re solenoid- Ill keep hold of it for the moment as I may have a go at wiring it in.
thanks
Hee hee - my thoughts exactly
Ringo
Posted: 06 Feb 2008, 21:03
by Kermit
You only need to connect one cable, this is to the solenoid behind the immobilser.
take a chisel to the plastic casing around the immobilser (smash off!!) to gain access to the fuel cut-off solenoid. connect this up....All other cables can be discarded
I had the same problem when converting my 1.7 to a 1.9 1Y engine.
Kerr
Posted: 28 Mar 2008, 13:33
by HarryMann
By the way, if you dont use your cold start solenoid could i have it
Aha! Do you find these pack up frequently Ringo (presuming its a barrel shaped thing, with bullet and cable facing aft) ?
Anyway, my whole coldstart setup removed as duff solenoid and AAZ just doesn't seem to need it when glo-plugs and compressions all good - even in deepest winter, though maybe a big sluggish until warm.
Posted: 06 Apr 2008, 16:42
by ringo
HarryMann wrote:By the way, if you dont use your cold start solenoid could i have it
Aha! Do you find these pack up frequently Ringo (presuming its a barrel shaped thing, with bullet and cable facing aft) ?
Anyway, my whole coldstart setup removed as duff solenoid and AAZ just doesn't seem to need it when glo-plugs and compressions all good - even in deepest winter, though maybe a big sluggish until warm.
Sorry about the delay - i dont get email replies on subscripted posts.
My 1Y always starts, but was a bit smoky on startup, apparently the cold start gets rid of this.
My cold start solenoid never worked - and a look round the local scrappies was fruitless.
Was thinking of wiring it up with either a capacitor or a timer to keep it on for 10 seconds after the glow plugs get turned off...
My new engine has one, so if all else goes well i might try it (if it works!).
Ringo
Posted: 06 Apr 2008, 22:22
by HarryMann
Ah thanks, so maybe the solenoid burn out or just packup for some reason...
Mine's a pump off a 306 or 405 Peugeot apparently (larger pulley drive taper), originally with all the gubbins but now just with throttle command and nowt else other than fuel solenoid connection - which as you say, starts fine without cold-start fuel and advance.
Sorry about the delay - i dont get email replies on subscripted posts
Why's that ? Bad email address or your profile hasn't got that option set?