Club 80-90 Forums

have fitted a factory r&r bed in the velle this came with a lower panel made from ply to finish off, thing is with the ply floor already fitted to the bus (genuine) the finishing panel is to high to fit under the bed.

does the ply floor finish up to this point on busses with this bed (the finishing panel is the thickness of the floor to high)or do i cut down the finishing panel(sorry need to take pictures to show what i mean)

cheers again guys

Hi, Don't know if this will help but I have just refitted my van floor and r&r bed. I got it all finished and then lay on the bed. Back ache!! Why not fit all the stuff, try laying on it and then trim off as necessary! It's easier to take a bit off than to add a bit! if you can't complete 'til it's all put together, why not try leaving it all loose (ie: not screwed down) until you are sure!
Again, not sure if this will help, hope it does!

ply floor already fitted to the bus (genuine)

Are you sure ???
we fitted a velle bed, genuine vw, and our floor had a layer of sponge stylr padding, molded to go round the "corrugation" of the floor

the panel fitted perfectly

Matt a poo

cheers for the replies guys
velle is an 84 that came with gen fixed bench seats that bolted to the floor the ply floor looks factory so i'm guessing it came with the van when new?
might remove it try panel an trim floor to it.
anyone else done this

cheers again

"Caravelles" NEVER had a ply floor... carpet with a thick insulation under it...
Sounds like you need to trim the panel to fit, thats easier... or make a new panel to fit...

^^^^^what he said^^^^^

I will be interested to see your end result - I am about to do the same!

Cheers

VW Lewis

[img]IMG:800:600]http://i51.photobucket.com/albums/f369/ ... 180429.jpg[/img][/img]
hi guys this bus defo came with a ply floor the seats bolted to the points shown in photo.
[img]IMG:800:600]http://i51.photobucket.com/albums/f369/ ... 180431.jpg[/img]
vwlewis easy job to fit but the latching points on the bus need moving forward see pic
[/img]
also want to fit a rear heater i have bought so need to know if this fixes to the ply or the metal
sorry i know it seams trivial but i dont want to cut anything until i'm sure

My early velle has a ply covered with some kind of hard plasticcy composite, very likely factory as perfect fit with perfect holes in all the right places, my late velle has spongy stuff that fits into floor pattern and would have had carpet over it.

Carat model caravelles def have a factory fitted ply floor, its a sod to get out if you need to, think they must have done it to hide the substantial metal bases that the rotating middle seats were fixed to, and maybe to keep it all on one level instead of a step down between cab and rear, the ducting for the factory Eber is under there too. it rests on about 4 lengths of timber if i remember right, poss some other 'velles had one as well.

Thanks for the tip frostbus .. what is the dangling black plastic bit for BTW?

Cheers

VW Lewis

VWlewis wrote:Thanks for the tip frostbus .. what is the dangling black plastic bit for BTW?

Cheers

VW Lewis

It clips over the end of the seat pin when in the bed position so no sharp edges !!

Thanks - good idea to protect the end of the locking rods ... I guess these fail quite quickly if they are used a lot so not often found on T25's... I will have to improvise with something else! Blue Peter time!

I have now completed my installation of the bed seat. Here is a write up of how I moved the headrests onto the bed seat from my original Caravelle seat

https://club8090.co.uk/wiki/He ... rear_seats

Cheers

VW Lewis

Sounds good - where can I get the VW bed kit?

Try Here

http://archive.club8090.co.uk/viewtopic.php?t=29923

or here

http://www.brick-yard.co.uk/forum/forum ... 23225&PN=2

Good Luck!

VW lewis