Page 1 of 2
rock n roll bed plans
Posted: 07 Nov 2006, 11:40
by kathyshack
has anyone got plans for making a rock n roll bed with jk hinges? I know in the past i have heard people have dimensions etc etc. would be great if anyone could e-mail me some....
thanks,
kathy
rock n roll bed plans
Posted: 07 Nov 2006, 11:52
by OLD ONE
GOT SOME. DONT KNOW IF THEY ARE JK, BUT MIGHT HELP..PM YOUR EMAIL ADDY. WILL SEND THEM
rock n roll bed plans
Posted: 07 Nov 2006, 12:33
by OLD ONE
Just sent. Hope it is of some help
Posted: 07 Nov 2006, 14:54
by kathyshack
Thanks Bob,
I think its reimo one though, so not sure if same as JK ones. Will take a clsoer look at it htough. - thanks!
Not sure still, whether to build one or go for one of the bluebird metal frame ones....
thanks again,
kathy
Posted: 08 Nov 2006, 13:36
by Dubkopfeyellow
We just made a bed out of JK hinges had to use the reimo plans but all worked out ok now the misses (who draws Assembly Instructions for furniture) is condsidering making a plan up for just this application
Just don't seem to be any anywhere that are that relevant!
rock& roll
Posted: 10 Nov 2006, 22:17
by Capt Jake
Have plans for a jk 3/4 if your still after one
rock and roll
Posted: 10 Nov 2006, 22:30
by Bowton Lad
Dubkopfeyellow wrote: all worked out ok now the misses (who draws Assembly Instructions for furniture) is condsidering making a plan up
Does 'er indoors work for MFI by any chance?
I've always wondered who was to blame for the drawings that look nothing like what you are trying to assemble......and then there's the instructions written in Hieroglyphics.
Posted: 11 Nov 2006, 20:30
by kathyshack
Capt Jake, that would be great, thanks
Posted: 13 Nov 2006, 08:50
by ermie571
Kathy,
we have just built the rnr bed from plans....They were all in german, and we only had a little bit of fiddling around to do when offering it up to the van.
I was really chuffed that it worked at all!
If there is anything I learned.....3 measures, one cut!!
The worst bit was getting the hinges bolted onto the upright supports in the right place. Had a couple of attempts, but got there in the end, with the assistance of a dob of paint on the end of a piece of wire to mark the position of the final hole....
But it works!!
Good luck
Emma
Posted: 13 Nov 2006, 11:29
by kathyshack
Thanks Emma,
I'm still in two minds whether to build one with JK hinges or to buy a bluebird one with the metal tubing. Not looking forward to drilling into the van though... don't want to drill into anything i shouldn't!
Posted: 29 Dec 2006, 11:20
by Zimbok
If anyone could e-mail the plans for the rock n roll bed I'd be very grateful. Thanks.
joneshow@gmail.com
Posted: 30 Dec 2006, 19:31
by lew
Zimbok wrote:If anyone could e-mail the plans for the rock n roll bed I'd be very grateful. Thanks.
joneshow@gmail.com
me too!!
theriff@jackassmail.com
Posted: 30 Dec 2006, 19:58
by ermie571
will nip upstairs and e-mail my plans to a moderator so they can go on the wiki...I am not capable!
Emma
x
Re: rock and roll
Posted: 03 Jan 2007, 12:34
by Dubkopfeyellow
Bowton Lad wrote:Dubkopfeyellow wrote: all worked out ok now the misses (who draws Assembly Instructions for furniture) is condsidering making a plan up
Does 'er indoors work for MFI by any chance?
I've always wondered who was to blame for the drawings that look nothing like what you are trying to assemble......and then there's the instructions written in Hieroglyphics.
No but her company does supply MFI I think (and they also do Instructions for other companies furniture too) so it could well be her fault although there instructions are pretty good
Posted: 04 Jan 2007, 10:52
by artymax
have they made it onto wiki yet? i'd really appreciate a copy if anyones got them?
maxine.church@virgin.net thanks