Club 80-90 Forums

OK ok ok - I have read the wiki.

I have the bolt and nut screwed down so that bush is flush with the bush..I can feel the hole. I tap away on the bolt and get absolutely NOWHERE!!! It resolutely fails to go in. Given up for today. Will try again tomorrow I guess.

perhaps I need a smaller hammer for the space...

Changed it once before, so I know it should bloody go in!!

Ultimate frustration!!!!

sorry.

Anyone in Medway done it recently care to give me a masterclass???


As Ghost said...character building.....

Em
xx

stick the bush in the freezer overnight then wipe it with engine oil just before you fit it.

have you got the right bush there are 2 different sizes

Faggie - really - two different sizes?? I ordered from breickwerks - only one was listed, sure of it? What size do I need??

Horizontal kipper....I'll try anything to get the bloody thing in....going to get it now.... xx

Em
xx

ermie571 wrote:Faggie - really - two different sizes?? I ordered from breickwerks - only one was listed, sure of it? What size do I need??

Horizontal kipper....I'll try anything to get the bloody thing in....going to get it now.... xx

Em
xx

6 volt and 12 volt starter bushes. wont be a problem on yours.

horizontal kipper wrote:

ermie571 wrote:Faggie - really - two different sizes?? I ordered from breickwerks - only one was listed, sure of it? What size do I need??

Horizontal kipper....I'll try anything to get the bloody thing in....going to get it now.... xx

Em
xx

6 volt and 12 volt starter bushes This happens alot on none stock pre 67vw's. wont be a problem on yours.

thanks kipper. Bush is in the freezer. Will it crack tomorrow?? xxx

Have you got the old bush out first? if not get a M12 tap put a small smear of grease on the tip wind it into the old bush when the tip of the tap bottoms out keep turning and the bush will wind itself up the tap and out.

oh, the old one is out, thanks!

Em
xx

Lets hope you don't have to shave your bush a bit.

ermie571 wrote:oh, the old one is out, thanks!

Em
xx

sorry i just read on another post you had removed it.

kevtherev wrote:Lets hope you don't have to shave your bush a bit.

Kev i like your thinking

we have a tool at work for fitting them, its not a hammer either, if you still have problems i could always post it to you to borrow if needed

Phil - that is a very kind offer! Thanks!! Gonna have another bash today....(providing we don't get the promised downpours) Will let you know.

again - thanks xx

Em
xx

ok, to provide an update.

I ordered a new starter motor and bush from brickwerks. They arrived and I bounced down to the van full of confidence. But the bush did not want to know. at all. I was told that I should be able to get it to bite a tiny bit...and then you can use the bolt with the nut screwed to tap it in. I tried it with the screw extractor...and just buggered the bush.

so, got another 3 at the parts shop today. Offered it up to the hole working from the engine bay and gave it a little twist....and it bit!!! It stayed there!!!! so gave it a little wiggle to get it out again, did the oil between the thumb and forefinger (place on thumb, fill with oil to brim of bush, then over the top and push down. Cleaned it off a bit so I could grip it.....twist it in and it still bit!! Then got the top bolt from the starter motor, screwed the nut on, and then put the bolt down inside the bush. The bolt goes in until the nut rests on the bush. Had a small hammer, and, still working from the engine bay, held the bolt and tapped gently with the hammer. stopped frequently to "feel" and ensure that a) it was going in, and b) I wasn't buckling it. Its pretty much in now....just got to go and tap the last ickle bit in!! Well chuffed with myself!!

Never know, bloody thing might start tomorrow! Not going to try and put the starter motor in....its brand new and I don't want to drop it!! (and hubby took the electrics off, so not sure where it all goes. Will do it with him tomorrow.

Em
xx

ermie571 wrote:ok, to provide an update.

I ordered a new starter motor and bush from brickwerks. They arrived and I bounced down to the van full of confidence. But the bush did not want to know. at all. I was told that I should be able to get it to bite a tiny bit...and then you can use the bolt with the nut screwed to tap it in. I tried it with the screw extractor...and just buggered the bush.

so, got another 3 at the parts shop today. Offered it up to the hole working from the engine bay and gave it a little twist....and it bit!!! It stayed there!!!! so gave it a little wiggle to get it out again, did the oil between the thumb and forefinger (place on thumb, fill with oil to brim of bush, then over the top and push down. Cleaned it off a bit so I could grip it.....twist it in and it still bit!! Then got the top bolt from the starter motor, screwed the nut on, and then put the bolt down inside the bush. The bolt goes in until the nut rests on the bush. Had a small hammer, and, still working from the engine bay, held the bolt and tapped gently with the hammer. stopped frequently to "feel" and ensure that a) it was going in, and b) I wasn't buckling it. Its pretty much in now....just got to go and tap the last ickle bit in!! Well chuffed with myself!!

Never know, bloody thing might start tomorrow! Not going to try and put the starter motor in....its brand new and I don't want to drop it!! (and hubby took the electrics off, so not sure where it all goes. Will do it with him tomorrow.

Em
xx

well done you