Page 1 of 2

Parts that should go in the bin

Posted: 25 Apr 2012, 10:00
by CovKid
Just thought I'd start this one off. A list of aftermarket parts that are either so badly made or do not match a T25 despite the claims.

I'll start with the 009 distributor - thump! (noise of one landing in bin) :D

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 10:20
by Titus A Duxass
Those cheap tacky dashboard jobbies - an ugly supply of squeaks and rattles.

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 10:22
by steve8090
Webber aftermarket carbs and GSF wheel bearings **(big thunk)**

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 10:28
by Cruz
Headlight eyebrows and eyelashes :lol:

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 10:45
by ghost123uk
JK bumper end caps = in the bin !



I will wait for some one else to say "almost anything JK sells" :run

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 10:52
by Ian Hulley
*clatter*

That was the JK catalogue btw :ok

*thud*

GSF dalek cap following it

Ian

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 11:08
by Mickyfin
Aftermarket door mirrors, thunk!

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 11:48
by ghost123uk
Empi exhausts and wheels = :clang:

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 11:59
by fodtommo
JK SIDE LOWER REPAIR PANELS... CLANG

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 13:39
by docklad
JK footwells....clang(but a weak thin, cling of a clang really, because of their "pooh" tin feel) and poor quality

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 13:42
by Ralf85
Cruz wrote:Headlight eyebrows and eyelashes :lol:

Leave Dirty Girty alone you big bully
:wink:
Patrick

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 13:54
by ghost123uk
I see JK are doing well so far, about time they did well at summat :rofl :rofl

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 13:58
by docklad
:rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl :rofl

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 15:04
by Cruz
Mickyfin wrote:Aftermarket door mirrors, thunk!
I disagree. I have had convex Hagus mirrors from Brickwerks and GSF and they were just as good as the old genuine mirrors and never moved

However GSF do sell a really dirt cheap £7 mirror that is crap

Re: Parts that should go in the bin

Posted: 25 Apr 2012, 15:06
by sjmtlewy
Cheap JK chrome hub caps. But you can at least reuse them as frisbees... if you dont mind getting rust on your hands.