Page 34 of 35

Re: Rustoration

Posted: 21 Sep 2026, 19:10
by RogerT
A selection of photos from recent progress.

Image
Brushing seam sealant under the gutter

Image
Tiger seal in seams

Image
Leftover rattle cans

Image
Slider off

Image
Back in for the passenger side

Hub nut currently soaked in plusgas. Didn’t budge when I put my full weight on a 5ft scaffold pole…


Sent from my iPhone using Tapatalk

Re: Rustoration

Posted: 15 Oct 2026, 16:21
by RogerT
Haven’t been keeping up to date…

Cracked off the hub nut after soaking in plugs for several days, applying heat, and then sitting on the scaffold pole and whacking with a hammer!

Removed the brake drum - just slid off easily
Image

Then onto the hub carrier nuts - again several days soaking and a 750mm breaker bar. Then the cv bolts - Allen headed - one rounded - got it to let go with a smackable impact driver.

The van is only lifted an inch on axle stands as that’s the only clearance I have for the garage door :-(. So I cut off the trailing arm
Image
Before attacking the bolts with a cutting disc. Here’s the bore for the bush on the outer mount - missing entirely
Image

Then after reading Adie’s Procrastinating thread, I started tackling the sill.

Priority is to preserve the cover plate (NLA) and the roller channel that’s fixed to the top of the outer sill and to the underside of the cover plate. Inspired by Adie claiming his cover plate just “popped off” I started locating and drilling the spot welds.

Days later I grabbed my grinder and a stack of cutting discs.Image

Image

Part of the outer sill
Image

A wee look above the rear jp - double skinned bodywork here, evidence of a "pooh" repair.
Image

After more cutting, sill mostly out.
Image

Et voila
Image

Sacrificed part of the front outrigger, but that’s not a problem. The main thing is I’ve kept the cover plate and roller guide intact. Here’s the roller track starting to wear through… seen from underneath.
Image

Here’s the rear end of the roller track
Image
Yes, it’s gone.

Order to be placed - base of B pillar repair piece, outrigger, inner and outer sill, triangular strengthener for base of C pillar, rear jp, trailing arm etc.

Edge of floor to be remade, B and C pillars to be remade, seatbox to be repaired, outer sill to be attached to roller guide, etc etc.


Sent from my iPhone using Tapatalk

Re: Rustoration

Posted: 15 Oct 2026, 16:27
by R0B
Blimey, that's one heck of a job. Well done you for tackling it.
:ok

Re: Rustoration

Posted: 25 Oct 2026, 16:37
by RogerT
Chipping away bitumen sound deadening to reveal … more rust…
Image

And the flashband that I had applied, to allow me to carve off the lower part of this panel
Image

Like so
Image

Remove the floor infill piece and the triangular piece that makes up the inner part of the lower C pillar…
Image
Image

And if I sneeze loudly the jacking point should just fall off!


Sent from my iPhone using Tapatalk

Re: Rustoration

Posted: 26 Oct 2026, 06:56
by dcworm57
That is one hell of project you have got there . Bloody well done  :ok

Re: Rustoration

Posted: 29 Oct 2026, 10:48
by RogerT
Sneeze completed
Image
Image
Image


Sent from my iPhone using Tapatalk

Re: Rustoration

Posted: 05 Nov 2026, 19:51
by RogerT
Shiny
Image


Sent from my iPhone using Tapatalk

Re: Rustoration

Posted: 06 Nov 2026, 09:52
by adamveitch
Looking good. I’m about to start work on the same bit. Still at the cutting stage.


Sent from my iPhone using Tapatalk

Re: Rustoration

Posted: 06 Nov 2026, 11:22
by totorro
Nice and shiny :)

I'm also tacking this area, turns out my left side front jacking point was mainly made of sikaflex and rust :(

Do you (or anyone else) have more photos of the interior of the jacking point structure? I need to reconstruct the strengthening plate for the b-pillar.

Re: Rustoration

Posted: 10 Nov 2026, 14:33
by RogerT
I'll post some up tonight

Re: Rustoration

Posted: 10 Nov 2026, 17:58
by RogerT
photos on this post viewable with a vpn, showing the inner b pillar

viewtopic.php?p=8315234&hilit=reinforce ... a#p8315234

Re: Rustoration

Posted: 10 Nov 2026, 18:03
by RogerT
alternative on big blue van

viewtopic.php?p=8282609&hilit=pillar#p8282609

I prefer his :ok

Re: Rustoration

Posted: 10 Nov 2026, 18:26
by RogerT
Positioning the outer suspension mount/jacking point.

Fix the inner sill in position - front end
Image

End on view of the front outrigger, showing the replacement part nicely lined up.
Image

And showing the end of the outrigger lining up with the vertical seam above
Image

The rear of the inner sill in position, with the jp clamped roughly in position.
Image

The trailing arm in position, with the hub at an appropriate height.
Image

Laser and straightedge clamped to the hub face. This ensures the laser is aligned with the hub face, and the laser can then be measured off the chassis rail at the front cross member, and further back towards the rear, to ensure the laser/straightedge/hubface is parallel to the chassis rail.
Image
Hmm, not the photo I hoped for. But you can see the laser beam, out of focus, on the straightedge.


Sent from my iPhone using Tapatalk

Re: Rustoration

Posted: 10 Nov 2026, 18:29
by RogerT
viewtopic.php?p=8229517&hilit=laser#p8229517

This shows the process on the drivers side, waaay back in 2018…


Sent from my iPhone using Tapatalk

Re: Rustoration

Posted: 11 Nov 2026, 11:34
by totorro
Thanks, I'll have a look :) Hopefully will get a chance to work on it this weekend.