Page 20 of 20
Re: Pierburg 2E3 choke
Posted: 09 Sep 2019, 15:11
by kevtherev
Stesaw wrote:I don't suppose you are still getting these made? My throttle arm snapped.

I have a spare.
Re: Pierburg 2E3 choke
Posted: 14 Sep 2019, 20:02
by Stesaw
kevtherev wrote:Stesaw wrote:I don't suppose you are still getting these made? My throttle arm snapped.

I have a spare.
Thanks Kev but the more I look into the carb the more I feel I should just outright replace it.
because when I took it off I noticed that It doesn't have the cone filter in the input side.
The pump injector snapped.. my fault as It was very much stuck and in my efforts to work it loose I snapped it... It did come out but the filter and rubber seal stayed in the carb as they were stuck inside sideways so I had to pull them out, looked crushed.. so that probably wasn't helping.
Obviously when taking it apart I split the gasket.(not a biggie I know rebuild kits are about £40ish)
It's also an early model (it has the 5 screws holding it together at the top.) part of me would like to dissasemble it and rebuild it but not sure if it would be worth spending on it compared to a £260 new reproduction from vwheritage... I'd imagine nowhere near £250 but not sure I want the hassle, especially if I keep either breaking things myself or finding more gremlins

.
Re: Pierburg 2E3 choke
Posted: 16 Sep 2019, 16:48
by kevtherev
The replacement Brosal Carburettor is not entirely perfect.
Money is better spent on restoration of yours.
Bromyard VW offer a 5 Star service.
Re: Pierburg 2E3 choke
Posted: 16 Sep 2019, 17:27
by Cobra88
I have a Bromyard'd Carb on mine
runs perfectly
Don't buy a Brosol
Re: Pierburg 2E3 choke
Posted: 16 Sep 2019, 22:40
by Stesaw
kevtherev wrote:The replacement Brosal Carburettor is not entirely perfect.
Money is better spent on restoration of yours.
Bromyard VW offer a 5 Star service.
Cobra88 wrote:I have a Bromyard'd Carb on mine
runs perfectly
Don't buy a Brosol
Just looked Bromyard up, it's a fair bit of cash for a refurb.. £395 puts that in webber carb territory and £295 for a repair is more than a new Brosol. I am sure they do great work, but if I am going to rebuild mine I'd like to do the work myself as I want to know as much as possible about the van. Maybe I should trawl Ebay for a 2e3 (I have put a Wanted add on the forums as well) and use it for parts to refub my one as I now also need a pump injector piece along with the plastic throttle arm.
Pierburg 2E3 choke
Posted: 18 Sep 2019, 19:16
by DoubleOSeven
Eurocarb will do it for £200. Recommend.
https://www.dellorto.co.uk/" onclick="window.open(this.href);return false;
Please don’t put a Weber on it, just don’t.
Re: Pierburg 2E3 choke
Posted: 18 Sep 2019, 19:45
by Mocki
DoubleOSeven wrote:
Please don’t put a Weber on it, just don’t.
What he said , just DONT ! You think it runs rough now , you ain’t seen nothing of the pain a Weber will bring .
Re: Pierburg 2E3 choke
Posted: 18 Sep 2019, 21:28
by Stesaw
Mocki wrote:DoubleOSeven wrote:
Please don’t put a Weber on it, just don’t.
What he said , just DONT ! You think it runs rough now , you ain’t seen nothing of the pain a Weber will bring .
To be fair I would rather just get another 2E or refurb mine.
Re: Pierburg 2E3 choke
Posted: 17 May 2020, 15:41
by patrickpawsey
I have to put my weight behind bromyard who know these carbs inside out. I have a remanufactured one from them and it is like, or better, than new.
In my experience, they will also give you a lot of information about reinstalling and running the carb, as well as about what was wrong with and rectified with the unit you send. It gives me a 'known good' starting point from which I can begin any future diagnostics and that -with something as complicated as the 2e3 - is golden.
So I wouldn't hesitate going with the repair from bromyard. If you want to learn about the carb and do a diy, getting a used one isn't a bad idea and following the videos, but beware that a lot of the rebuild kits are but very good, and even in the good ones, things like the float valve seals are not great, and you should in fact keep the original pierburg if you have it, and it's not in bad condition. Either way good luck and have fun
Sent from my ONEPLUS A3003 using Tapatalk
Re: Pierburg 2E3 choke
Posted: 18 May 2020, 07:19
by dontpanic
Late coming into this thread and it suddenly dawned on me that I haven't got the plastic choke linkage as I bought my carb and throttle linkage separately.
Does anyone still have one and how can I buy it?...
Thanks
Re: Pierburg 2E3 choke
Posted: 19 May 2020, 18:17
by kevtherev
I'll have a look
Re: Pierburg 2E3 choke
Posted: 19 May 2020, 19:06
by maxstu
If Kev cant help PM me.
Regards
Stuart
Re: Pierburg 2E3 choke
Posted: 20 Nov 2026, 10:26
by Erithacus
CJH wrote: ↑31 Aug 2017, 20:21
It's been almost 18 months and 6,000 miles since I fitted my test carb to my engine, complete with both the 3D printed parts, and since I recently removed the carb to fit a new engine I thought it would be worth taking a look at those two parts to see how they've coped with the heat of the engine bay.
First up, the choke part. It's a bit grubbier, but there are no obvious signs of ageing - the holes don't appear to have ovaled, and there's no yellowing, cracking or other signs of deformation that I can see.
The throttle part seems fine too. There's a nice well-defined wear line where it rides on the throttle cam, and it appears to be in about the same place as the wear line on an original part. The 3D printed part is made of Nylon, which is somewhat self-lubricating, so I deliberately did not oil the cam when I fitted the part - oil would tend to attract dust and increase the wear I suspect.
Again, no other signs of ageing. The DIY spindle, made from a flat headed rivet and a spacer tube, is still holding the part firmly while allowing it to rotate freely, and the part itself seems no different from when it was fitted.
I've had a steady trickle of interest in these parts (several images from this thread show up on the first page if you Google for images of 'Pierburg choke' for instance), but there are still plenty available. For the benefit of anyone who hasn't seen this thread before, I sell these parts more or less 'at cost': the choke part is £1, and the throttle part (including the spacer and some rivets) is £1.50, plus £1 postage to cover 'several' of these parts (I've not yet had an order for enough to take the postage over £1).
Sorry to revive this old thread but my brother and I are restoring our childhood ride and we need the replacement choker lever part for Pierberg 2E3 28/30.
I'm looking to 3d print the part in Nylon, would you be able to share the 3d model so I can source the printing somehere here in Belgium?
Also is it still holding up?

Many thanks in advance!