Page 2 of 3
Posted: 31 May 2006, 19:27
by Don-Tucker
Where can I get these parts Harry ?
Don
Posted: 31 May 2006, 20:20
by HarryMann
Wiki on gearchange selctors
Er, VW only, they're not a lot of dosh, the recommended VW polylube is a fortune, many use Medium/Light Moly grease, I've used a waterproof grease (Mobil Blue in tubes) instead...
Inspect the bellows first, see which ones you need...
first check the spider and see if you can detect wear in it.. some say they do get sloppy, I've always found them 'reasonable' - its a good design, bt if nothing else, pop the pins out clean old sticky grease and re-lube it.
I intend eventually putting up a full length photo(s) of the whole selection mechanism - but it won't be tonight!
Posted: 03 Jun 2006, 08:10
by Don-Tucker
Out of interest JK do gear linkage bushes and bits now,just had their catalogue.
Don
Posted: 03 Jun 2006, 10:28
by HarryMann
Thats handy, will Wiki it... doubt if they do the full front floor bal-joint repair kit though.
Posted: 03 Jun 2006, 15:58
by Don-Tucker
No you are right Harry ,it looks like everything after the front bulkhead.I still can't get over the difference my little mod. made,going to give it a run up to Elan Valley tomorrow,I'm all excited.
Don
Posted: 03 Jun 2006, 16:10
by HarryMann
Elan valley, we happened past that looking for the Syncropendence site last year... quite a beauty spot and a nice road up there.
Presumably the Lotus Elan would be at home on such a pretty and twisty stretch...
Posted: 03 Jun 2006, 16:15
by Don-Tucker
Depends on the weather
We are due for a spell of sunshine.
Don
Posted: 03 Jun 2006, 16:27
by HarryMann
Hot as an oven here in Herts at the moment.. phew
NOT
Posted: 05 Jun 2006, 08:15
by toomanytoys
Cheers Don.. Well, my kit does work a treat..
Know of any lathe/mill/combination, going for sensible money? My workshop is comming along nicely..
Posted: 05 Jun 2006, 12:41
by banana
is there a kit for the 1.6TD yet?
Posted: 05 Jun 2006, 14:45
by HarryMann
Ha, tell me the diffeernces you perceive there banana please...
Posted: 05 Jun 2006, 14:59
by Don-Tucker
Only on E-Bay,maybe or Machinery Mart ,Toomanytoys. A combination is a good idea if space is in short supply.
It was lovely up at Elan Valley Sun, talking to another camper with a T4 Riemo .Glad I have the T25.
Don
Posted: 05 Jun 2006, 15:03
by banana
By your reply I see you think I'm a sandwich short but my response was prompted by what I read on the WIKI having gone to Simon Whitmores page where he excluded TD's from the kit. Now being cautious and interested in this mod i did not want to get the typical bad luck i have and strip the linkage down to find It didnt work. So from Simons pics mine does not look the same as his pic shows a gear stick mounted on a housing hump whereas my shift is set into the flat slope.
Posted: 05 Jun 2006, 15:12
by Horza
I also thought there was a diference between the TD and the rest of the world as far as fitting short shifters, is this not so?
Posted: 05 Jun 2006, 17:17
by HarryMann
Was seriously asking if you or anyone could say which of the TD features, floor plate, gearlever or ? is the bit that prevents it being fitted.