Club 80-90 Forums

Posh,

You took the steel loadbed off, and (somehow) put it back on again ???

Is that magic wand or welding torch I see

The old loadbed had a couple of small holes in it and rot along the transverse seam. Add to that lots of dents and that's the reason it came off.

Lots of spot welds drilled out and careful grinder work was needed to do this.

Now its been replaced with a genuine new one from Neuffer in Germany.

Lots of brush in seam sealant on the edges and Tiger Seal was used to 'bed' it down onto the rails.

Moving on we have the new load bed with cab protector in place for trial fitting/adjustment:


And one of the tricky bits I decided on, the remodelled engine hatch:


And here's another modified part. An alternative to the standard engine access hatch:


It's an idea I have toyed with since I got the Syncro. I changed my mind a few times and even nearly sold the Caddy panel once. Sense prevailed though and here it is.

The number plate needs relocating but again, there is a cunning plan in progress for that too [;)]

Andy had to put a lot of time into this as it wasn't simply a case of welding one flat panel to another. The Doka hatch actually curves. Couple that with the fillet along that top edge and you are in for some steady metal bashing. Worth it though I reckon.

Ok, its in for lots of primer and rubbing down now. One side is pretty good, the other has more than a few dents along it.



Andy has given 80% of it a first 'round' with the DA which hasn't shown any nasties, just some minor dips which he is attending to very patiently.



The engine access hatch has now been fitted and looks even better than I expected in primer.



I'm working on the relocated number plate mount at the moment. No further modifications to the metalwork (don't quote me) so it's all steam ahead for more prep and a basecoat.

Now its been replaced with a genuine new one from Neuffer in Germany.

Lots of brush in seam sealant on the edges and Tiger Seal was used to 'bed' it down onto the rails.

Ah! You must be the only one in the world to buy and fit one then ! Fitted properly too. Sounds like the job gains momentum weekly!

Lots of spot welds drilled out and careful grinder work was needed to do this.

Have helped do one so I know how many, a lot of work, specially cleaning up afterwards - but the access is rather good till the new one goes on.

Hello Brian ! It is not necessary to remove the bed to replace the side panels - it is easier though - but once you change the entire rear end such as side panels, wheel arches and rear corners you have good access to all welding spots. It is a pain in the ass if you want to drill off and re-install the existing bed... But like Paul`s project shows - there is still an amount of rust under the bed - so sandblasting could be one option.

BR from germany


Lars

Hehe....looks like those parts found a good home eh, Lars?

Thanks for the easy transaction/delivery. Can't wait to get those Tristar parts fitted.

Looking forward to seeing the finished article; going to be a one-off by the sounds of it!

Hello Brian ! It is not necessary to remove the bed to replace the side panels - it is easier though - but once you change the entire rear end such as side panels, wheel arches and rear corners you have good access to all welding spots. It is a pain in the ass if you want to drill off and re-install the existing bed... But like Paul`s project shows - there is still an amount of rust under the bed - so sandblasting could be one option.

Might save a bit of work if the loadbed can stay in! I wasn't intending to remove the rear panel as it's in good condition so hopefully when we take the side panels off we'll have a better idea how to proceed.

Poshbuggers - sorry for hijacking your thread!

Cheers

Brian

Knocked up a quick 'concept' drawing in Photoshop yesterday which I thought I would share with you.

[IMG:600:300]http://www.poshbuggers.co.uk/crewie-design.jpg[/img]

It's pretty much how the Syncro will look for a while, but I do have plans for a more outrageous cage/bullbar/rack system which I hope to sort towards the end of the year.

The setup pictured will do while I get solid measurements and will suffice for my annual excursion to Germany in August.

Got the canvas/frame and roofrack sorted, just a bullbar to arrange now.

Cool..
Shall have to do my floor too.. its a lot worse than yours sounded! just patched and covered with marine ply so it can be used... So many other bits to fix, but it keeps running... 28k km since July last year....

I rather like those marine ply loadbeds, you can shovel stuff onto and off them easier

Trouble is, bits keep getting in that silly hollow section behind the bumper, through those stuppid elongated holes - must do a fix for shovelling "pooh"

Posh, impressive drawing - looks like the handrails for steps leading down from the cab into a covered paddling pool in the back - neat

Now there's a 'Pimp my ride' idea if I ever heard one (yuk!)

No thats a spare wheel cover LOL

finished colour has got to be lime green as the T5!