Difference between revisions of "Syncro Prop Shaft removal refurbishment and refitting"
m |
m |
||
| Line 38: | Line 38: | ||
T : 01538384278 F : 01538371265 | T : 01538384278 F : 01538371265 | ||
'''Aidan:''' GKN Driveline at Leek (from an August 2010 post) | |||
I have had their own made ones before, sliding joint and standard DIN 90 UJ's with grease nipples less than £200 and I recently had two shafts refurbished by them after my attempts had failed, you can fit a trunion kit from Baxter (Brickwerks) but they don't necessarily come right without some black magic to sort end float and balance as I have discovered; they did two for £135 plus VAT in 24 hours sorted and repainted. | |||
I delivered and collected they are just over an hour from me, but I'm sure they can sort shipping/collection if required but good to use local if possible. GKN have more than 1 depot anyway, it was Andy Simpson who found the Leek one and pointed me at it. | |||
---- | ---- | ||
Latest revision as of 00:28, 2 August 2010
HarryMann: Propshaft bolts from Syncro-Nutz or SyncrosparesUK or VW Commercial Parts counter
Use the correct ones, bolts about £1 each, locknuts (STOVER) M8 fine thread New is best because if prop is on/off/on/off a lot then they will stand some rounding off (access can be a bit angled and awkward at times)
VW part nos. for the correct nuts and bolts
Bolts N 010 102 3 £1.53 ea. (M8 x 1.00 x 25)
Nuts N 022 152 1 £0.26 ea. (STOVER - All metal locking)
EIGHT required.
Syncro Parts - Bolts propshafts
Rogerthecat from brickyard thread http://www.brick-yard.co.uk/forum/forum_posts.asp?TID=33617&KW=propshaft&PID=255375#255375
2 weeks ago the ScoobyVelle developed a vibration that would collapse a house. Captain Know Everything from Huddersfield immediately said it was the prop (and that was at 45 miles distance) and advised dropping the prop - Aiden also pitched in with brilliant help and advice - thanks. Off came the prop and it all went very quiet, calm and economical - the handling however, all turned to worms and the van became very skittish especially on wet roads and leaves whereas previously it had only ever faltered on a huge diesel slick on the A57. Eventually I manage to get the prop into GKN yesterday morning at about 0930. They said they would get fixed or build a new one, whichever was the best/most economical route. Called this morning at 10 am to be told - it's ready - refurbed with new joints, rubber doughnut ok as is all else - has been tested and rebalanced all for the princely sum of £54. Subject to testing on the van I think that is one hell of a service - so thanks GKN!
GKN Driveline Service Ltd.
Industrial & Distribution Services,
Higher Woodcroft, LEEK, ST13 5QF
T : 01538384278 F : 01538371265
Aidan: GKN Driveline at Leek (from an August 2010 post)
I have had their own made ones before, sliding joint and standard DIN 90 UJ's with grease nipples less than £200 and I recently had two shafts refurbished by them after my attempts had failed, you can fit a trunion kit from Baxter (Brickwerks) but they don't necessarily come right without some black magic to sort end float and balance as I have discovered; they did two for £135 plus VAT in 24 hours sorted and repainted.
I delivered and collected they are just over an hour from me, but I'm sure they can sort shipping/collection if required but good to use local if possible. GKN have more than 1 depot anyway, it was Andy Simpson who found the Leek one and pointed me at it.
Although it may be better to have your OEM VW one refurbished:
A1 Props Bootle 0151-944-1586
The original prop can have its UJs replaced and be rebalanced. Prop shops do this, but the above is the cheapest anyone has found for the Syncro prop.
