Bodywork and Glass Tailgate lock - Revision history

CovKid at 23:17, 3 December 2015

2015-12-03T23:17:12Z

← Older revision		Revision as of 23:17, 3 December 2015
Line 1:		Line 1:
	~~'''Under construction'''~~

	(Penned by Petethefeet)		(Penned by Petethefeet)

CovKid at 23:16, 3 December 2015

2015-12-03T23:16:47Z

← Older revision		Revision as of 23:16, 3 December 2015
Line 32:		Line 32:
	Make a note of the order of the parts.		Make a note of the order of the parts.
	At this point make sure the key is in the lock and then with draw the barrel		At this point make sure the key is in the lock and then with draw the barrel


			[[image:tgate10.jpg]]

	The seal is broken so I will replace it with an O ring when I rebuild the lock.		The seal is broken so I will replace it with an O ring when I rebuild the lock.
	As I was going to replace the tumblers I pulled the key out and all the springs and tumblers fell out. These are very small!!!!		As I was going to replace the tumblers I pulled the key out and all the springs and tumblers fell out. These are very small!!!!

			[[image:tgate11.jpg]]

	The barrel was cleaned up with carb cleaner and the new tumblers fitted using the old springs. 5 from one side and 2 from the other		The barrel was cleaned up with carb cleaner and the new tumblers fitted using the old springs. 5 from one side and 2 from the other

			[[image:tgate12.jpg]]

			[[image:tgate13.jpg]]

	The lock was then re assembled as it came apart having clean all the parts up and lightly greased		The lock was then re assembled as it came apart having clean all the parts up and lightly greased

			[[image:tgate14.jpg]]

	The tab was located in the plastic housing and the circlip refitted.		The tab was located in the plastic housing and the circlip refitted.

			[[image:tgate15.jpg]]

CovKid at 23:14, 3 December 2015

2015-12-03T23:14:08Z

← Older revision		Revision as of 23:14, 3 December 2015
Line 20:		Line 20:
	The barrel is then pulled out of the plastic housing.		The barrel is then pulled out of the plastic housing.

			[[image:tgate5.jpg]]

			The arm on the end of the lock is then released by carefully knocking out the roll pin

			[[image:tgate6.jpg]]

			[[image:tgate8.jpg]]

	~~The arm on the end of the lock is then released by carefully knocking out the roll pin~~		[[image:tgate9.jpg]]

	Make a note of the order of the parts.		Make a note of the order of the parts.

CovKid at 23:12, 3 December 2015

2015-12-03T23:12:37Z

← Older revision		Revision as of 23:12, 3 December 2015
Line 7:		Line 7:
	The lock assembly was removed by removing all three of the screws that hold the lock assembly into the boot lid, initially I only took the centre one out but I could not get the lock out		The lock assembly was removed by removing all three of the screws that hold the lock assembly into the boot lid, initially I only took the centre one out but I could not get the lock out

	image		[[image:tgate1.jpg]]

			[[image:tgate2.jpg]]


	The barrel assembly is then removed from the lock by priseing out the circlip with a small screwdriver.		The barrel assembly is then removed from the lock by priseing out the circlip with a small screwdriver.

			[[image:tgate3.jpg]]

			[[image:tgate4.jpg]]

	The barrel is then pulled out of the plastic housing.		The barrel is then pulled out of the plastic housing.



	The arm on the end of the lock is then released by carefully knocking out the roll pin		The arm on the end of the lock is then released by carefully knocking out the roll pin

CovKid: Created page with ''''Under construction''' (Penned by Petethefeet) I have just replaced the tumblers in the boot lock on my 1982 devon; I thought I would post some pictures to help others. I was…'

2015-12-03T22:52:23Z

Created page with ''''Under construction''' (Penned by Petethefeet) I have just replaced the tumblers in the boot lock on my 1982 devon; I thought I would post some pictures to help others. I was…'

New page

'''Under construction'''

(Penned by Petethefeet)

I have just replaced the tumblers in the boot lock on my 1982 devon; I thought I would post some pictures to help others.
I was changing the tumblers to suit my new sliding door lock.
The lock assembly was removed by removing all three of the screws that hold the lock assembly into the boot lid, initially I only took the centre one out but I could not get the lock out

image

The barrel assembly is then removed from the lock by priseing out the circlip with a small screwdriver.

The barrel is then pulled out of the plastic housing.

The arm on the end of the lock is then released by carefully knocking out the roll pin

Make a note of the order of the parts.
At this point make sure the key is in the lock and then with draw the barrel

The seal is broken so I will replace it with an O ring when I rebuild the lock.
As I was going to replace the tumblers I pulled the key out and all the springs and tumblers fell out. These are very small!!!!

The barrel was cleaned up with carb cleaner and the new tumblers fitted using the old springs. 5 from one side and 2 from the other

The lock was then re assembled as it came apart having clean all the parts up and lightly greased

The tab was located in the plastic housing and the circlip refitted.