Sliding door handle wobble - Why?

Thin bits of metal and bright blue light. Including glass & trim.

Moderators: User administrators, Moderators

Heaver
Registered user
Posts: 13
Joined: 12 Mar 2021, 07:35
80-90 Mem No: 0

Sliding door handle wobble - Why?

Post by Heaver »

So, there is some wobble in the door handle on both of my sliding doors.

Seems very common and doesn't seem to cause a huge issue, apart from scratching paintwork.

But.... why does it wobble?

It seems to door only locks when the handle is pushed towards the door, so its seems like its supposed to.

Also, when you remove the handle, I can see that there is a collar which moves against the door handle....

So why?

User avatar
T3luestar
Registered user
Posts: 671
Joined: 07 May 2012, 10:31
80-90 Mem No: 13845
Location: Widnes

Re: Sliding door handle wobble - Why?

Post by T3luestar »

Take the door card off from the inside and you should see a screw on the other side of the handle. Probably just needs nipping up.

Heaver
Registered user
Posts: 13
Joined: 12 Mar 2021, 07:35
80-90 Mem No: 0

Re: Sliding door handle wobble - Why?

Post by Heaver »

The screw is (was) tight.  

I noticed you can buy a grommet/collar made of rigid plastic, which is designed to stop the wobble.  I'm going to design and 3d print my own, but wondered if the wobble was intended or just wear/age.

User avatar
Aidan
Trader
Posts: 7486
Joined: 11 Oct 2005, 19:21
80-90 Mem No: 742
Location: Llanfyllin, mid Wales : )

Re: Sliding door handle wobble - Why?

Post by Aidan »

often the handle has been removed previously and the square holed washer gets lost in the bottom of the door when withdrawing it, peeps don't realise its there and so don't replace it when reassembling

the foam seal is usually degraded and missing too, I don't know if any vendor this side of the pond still has the foam seal
Image

oddly the spacer washer with the square hole isn't shown in Bentley for the later lock, nor listed in the parts catalogue for the later years but it is a thing, carried over from the bay

Image

part number 211 843 717; I recently added one to my wobbly handle which also had fully tightened screw on the inside and low and behold the wobble that allowed handle to scratch and wear away the paint was sorted - I'm not sure if anyone other than heritage have them in stock
AIDAN :)

User avatar
slowcoach
Registered user
Posts: 1689
Joined: 06 May 2010, 10:23
80-90 Mem No: 8892
Location: West Yorkshire
Contact:

Re: Sliding door handle wobble - Why?

Post by slowcoach »

That's interesting Aidan, I've never seen that either. Our handles been off many times. It has a reasonable wobble to it, but doesn't scratch the paint.

One more for the 'one day' list

Sent from my Pixel 4 using Tapatalk

===================
1984 TRAKKA Conversion Subaru EJ20 5 Speed

Heaver
Registered user
Posts: 13
Joined: 12 Mar 2021, 07:35
80-90 Mem No: 0

Re: Sliding door handle wobble - Why?

Post by Heaver »

I don't seem to have the square holed washer.... thats interesting.

I figured out what the moving part is within the door (I mentioned initially).  The moving part moves across then the key is used, and slides across to (un)lock the door.

Where does the squared holed washer site in relation to the mechanism?

Heaver
Registered user
Posts: 13
Joined: 12 Mar 2021, 07:35
80-90 Mem No: 0

Re: Sliding door handle wobble - Why?

Post by Heaver »

Heritage describe it as a shim... i guessing it sits under the screw on the inside of the door pulling the handle in.

silverbullet
Trader
Posts: 17909
Joined: 08 Jun 2009, 09:51
80-90 Mem No: 6908
Location: Surrey Syncronaut #156
Contact:

Re: Sliding door handle wobble - Why?

Post by silverbullet »

Heaver wrote: ↑21 Jul 2024, 07:22 Heritage describe it as a shim... i guessing it sits under the screw on the inside of the door pulling the handle in.
It goes between the lock assembly and the inside handle afaik
1985 Oettinger 3.2 wbx-6 Caravelle RHD syncro twin slider. SA Microbus bumpers, duplex winch system, ARC 7X15 alloys,
"Schrödinger's syncro"
Syncronaut #156

User avatar
Aidan
Trader
Posts: 7486
Joined: 11 Oct 2005, 19:21
80-90 Mem No: 742
Location: Llanfyllin, mid Wales : )

Re: Sliding door handle wobble - Why?

Post by Aidan »

as Ian says it goes on the square shank of the handle before the handle is fitted into the lock, you'd fit the rubber seal to the door and the foam seal to the round shank of the handle before inserting it - now it is possible there are slight variations in the door handles which meant the square holed washer was deleted in 1986 as the handle was suffix E by the end of production, and there may be variants of the lock too, so it maybe fitting a new or used late 'late' handle to an early 'late' van say from 1985 there is a slight difference so maybe the square holed washer isn't needed in all cases, but I've found a number of the washers in the bottom of doors (bought used or stripped for parts) or on the floor after door lock has been worked on; with used ones all you know is it is late type but not always which year the van it came from was or exactly which handle/lock was fitted originally - the handles break and get replaced with used or new with increasing frequency they aren't the strongest thing in the world,
And when was the last time you took the handle out and found the foam seal present and intact ? I haven't seen one for many years, the first van (1986my) I broke for parts in 2004 still had it but it was turning to dust and broke up when removed
AIDAN :)

cjaysx
Registered user
Posts: 55
Joined: 23 May 2022, 14:57
80-90 Mem No: 17636
Location: Southampton, UK

Re: Sliding door handle wobble - Why?

Post by cjaysx »

Hi Aidan,

Massive thanks for the info in this thread. I've got the same issue and have been hunting for the shim, the only place I can find it is in Norway though..

https://www.folkevogn.no/product/volksw ... -211843717

Is anyone aware of any other website that has it in stock?

Thanks, Colin

Simon Baxter
Trader
Posts: 3200
Joined: 08 Oct 2005, 19:36
80-90 Mem No: 1
Location: Huddersfield, WeYo.
Contact:

Re: Sliding door handle wobble - Why?

Post by Simon Baxter »

cjaysx wrote: ↑10 Nov 2026, 21:31 Hi Aidan,

Massive thanks for the info in this thread. I've got the same issue and have been hunting for the shim, the only place I can find it is in Norway though..

https://www.folkevogn.no/product/volksw ... -211843717

Is anyone aware of any other website that has it in stock?

Thanks, Colin
I have a sample somewhere, if I can find it i'll get some made.
 
'86 VW T3 syncro panel
'89 VW T3 Westy Atlantic
'81 Porsche 924
SJ Baxter LTD/Brickwerks

shepster
Registered user
Posts: 1761
Joined: 12 Oct 2005, 11:14
80-90 Mem No: 1342
Location: Wolverhampton.

Re: Sliding door handle wobble - Why?

Post by shepster »

2.1 DJ running on carb and LPG.

User avatar
mioba
Registered user
Posts: 658
Joined: 10 Jul 2009, 11:48
80-90 Mem No: 7850
Location: Nottingham

Re: Sliding door handle wobble - Why?

Post by mioba »

Postage is from Germany so it makes it very expensive.
Westfalia Hightop Top Joker 1.6TD - aka Daisy, my labour of love

User avatar
tobydog
Registered user
Posts: 1557
Joined: 07 Mar 2009, 21:03
80-90 Mem No: 6484
Location: Near Saarfend, Essex

Re: Sliding door handle wobble - Why?

Post by tobydog »

shepster wrote: ↑Yesterday, 08:09 https://ebay.io/m/kpCJBo

That could be filed out of a suitable thin piece of steel sheet...
Knowledge is power
1970 CU

shepster
Registered user
Posts: 1761
Joined: 12 Oct 2005, 11:14
80-90 Mem No: 1342
Location: Wolverhampton.

Re: Sliding door handle wobble - Why?

Post by shepster »

mioba wrote: ↑Yesterday, 17:32 Postage is from Germany so it makes it very expensive.

Just providing the info people were asking for, I bought 2 so happy to pay £17 delivered.
2.1 DJ running on carb and LPG.

Post Reply