The T3200E thread
Moderators: User administrators, Moderators
Re: The T3200E thread
Ohh metal porn
2.1 LPG/Petrol Auto Caravelle
"The difference between genius and stupidity is that genius has its limits"
"The difference between genius and stupidity is that genius has its limits"
-
- Registered user
- Posts: 715
- Joined: 28 Nov 2020, 16:36
- 80-90 Mem No: 17435
Re: The T3200E thread
It's absolutely automotive filth. I'd say this thread deserves a NSFW heading.
1988 Caravelle - FB25B - Syncro converted
2016 MB E63 AMG S - The daily driver
2019 Harley Fat Bob - The leisure
2016 MB E63 AMG S - The daily driver
2019 Harley Fat Bob - The leisure
ZsZ wrote: WOW! thats seems simply not right.
-
- Trader
- Posts: 16342
- Joined: 08 Jun 2009, 09:51
- 80-90 Mem No: 6908
- Location: Surrey Syncronaut #156
- Contact:
Re: The T3200E thread
Saturday morning, Hoopers dog class was cancelled, lets get this cam timed.
Chill out tunes on the DAB, because its a faff.
Split pvc hose stops the rods falling over and trying to jab/tangle/chip anything when taking the case half on and off*
Protractor, dial gauge, paint and a sharp scriber to mark the centre line at max lift.
*wooden wedge to lock the cam
Just keep rotating the cam one bolt at a time (always go the same direction!) and trying different teeth until it chimes in...
Chill out tunes on the DAB, because its a faff.
Split pvc hose stops the rods falling over and trying to jab/tangle/chip anything when taking the case half on and off*
Protractor, dial gauge, paint and a sharp scriber to mark the centre line at max lift.
*wooden wedge to lock the cam
Just keep rotating the cam one bolt at a time (always go the same direction!) and trying different teeth until it chimes in...
-
- Trader
- Posts: 16342
- Joined: 08 Jun 2009, 09:51
- 80-90 Mem No: 6908
- Location: Surrey Syncronaut #156
- Contact:
Re: The T3200E thread
I also lock the flywheel with a simple strap once I have found TDC, the zero the protractor wheel, rotate the crank to the desired angle (I favour max inlet valve lift at 112° ATDC for both std and my "performance" grinds) then lock it again. It also pulls the crank back against the thrust face, which prevents any unwanted helix angle errors caused by the cam gear and is a lot less bulky than working around the flywheel.
Last edited by silverbullet on 11 Dec 2021, 15:42, edited 1 time in total.
-
- Registered user
- Posts: 296
- Joined: 08 Jul 2014, 09:23
- 80-90 Mem No: 13990
- Location: 10 miles south of Bristol
Re: The T3200E thread
Despite the fact that I’ve played around with cars, motor-bikes, tractors, lawn mowers etc since I was old enough to pick up a spanner. it’s only when I read this sort of stuff that I realise how little I actually really know about the internal combustion engine!
-
- Trader
- Posts: 16342
- Joined: 08 Jun 2009, 09:51
- 80-90 Mem No: 6908
- Location: Surrey Syncronaut #156
- Contact:
Re: The T3200E thread
Transforming domestic steel door hinges into oil baffle gates. One side cropped off, holes welded up and dressed down, straightened, rivet pins removed and free-running - aka loose - 4mm wire refitted with ears to limit their opening angle (no more than 60 degrees opening required otherwise they take too long to shut and become less than useful)
- Robsey
- Registered user
- Posts: 1169
- Joined: 19 May 2012, 20:45
- 80-90 Mem No: 11137
- Location: East Manchester
Re: The T3200E thread
PeteandNikki wrote: ↑11 Dec 2021, 14:12 ...it’s only when I read this sort of stuff that I realise how little I actually really know about the internal combustion engine!
I have to agree.
Amazing to see the detail and precision in your work.
I spent most of New Years Eve night reading the whole thread - looking for motivation to refurbish my DJ.
Now I realise, that I am just playing in the kiddie-pool compared to proper stuff like this.
The only thing that I have to add is -
The wasserboxer engines are not your typical internal combustion engines. They are a breed of their own.
The Oetti engine "after-thought" design appears to be a dozen steps beyond that.
Keep going, loving this thread.
1983 Tin Top with a poorly DF and 4 speed DT box.
1987 Electrics and a DJ engine.
Maybe one day I might get it finished
1987 Electrics and a DJ engine.
Maybe one day I might get it finished
-
- Trader
- Posts: 16342
- Joined: 08 Jun 2009, 09:51
- 80-90 Mem No: 6908
- Location: Surrey Syncronaut #156
- Contact:
Re: The T3200E thread
It would be easy to say that I am starting to regret this sump baffle, its going to be a bugger to install. But Magnus Magnusson rules apply:
I have started, so I will finish.
The wbx6 really is an afterthought engine, for the sake of a few mm here and there it could have been a lot more durable. But it is what it is. Strangely, the early Subaru EA pushrod engines are closely based on the wbx design and even the EJ engines shared the same bore spacing of 113mm.
Anyway, I'll get there soon. Closing the crankcase will be a big moment.
I have started, so I will finish.
The wbx6 really is an afterthought engine, for the sake of a few mm here and there it could have been a lot more durable. But it is what it is. Strangely, the early Subaru EA pushrod engines are closely based on the wbx design and even the EJ engines shared the same bore spacing of 113mm.
Anyway, I'll get there soon. Closing the crankcase will be a big moment.
-
- Trader
- Posts: 16342
- Joined: 08 Jun 2009, 09:51
- 80-90 Mem No: 6908
- Location: Surrey Syncronaut #156
- Contact:
Re: The T3200E thread
Still not enjoying this job. Endless trimming and fitting but its coming together. I may have to split the baffle and mount part of it on the oil pickup, not sure atm.
-
- Registered user
- Posts: 7
- Joined: 10 Jan 2012, 17:08
- 80-90 Mem No: 0
- Location: Sandton, Gauteng, South Africa
Re: The T3200E thread
Hi there,
Just wanting to know whether this thread of engine build is now complete, as if I’m
following things correctly, the engine is now actually mounted in the bus as per your other thread Our Syncro Caravelle? Will that be the thread to follow going forward?
Just asking and thank you for the amazing info, skill and knowledge you share with us all!
Just wanting to know whether this thread of engine build is now complete, as if I’m
following things correctly, the engine is now actually mounted in the bus as per your other thread Our Syncro Caravelle? Will that be the thread to follow going forward?
Just asking and thank you for the amazing info, skill and knowledge you share with us all!
-
- Trader
- Posts: 16342
- Joined: 08 Jun 2009, 09:51
- 80-90 Mem No: 6908
- Location: Surrey Syncronaut #156
- Contact:
Re: The T3200E thread
Engine not finished yet, a few final details to sort out. Once the exhust is made I will be doing the final assembly and then getting it running.
-
- Trader
- Posts: 16342
- Joined: 08 Jun 2009, 09:51
- 80-90 Mem No: 6908
- Location: Surrey Syncronaut #156
- Contact:
Re: The T3200E thread
Things have ground to a halt as I had to put the empty engine case with heads fitted etc back in the bus while it went away for exhaust fitting. Might get it back in August, but in the meantime I did receive a pair of custom-made split shims to correct the over-cut thrust face on the rear main bearing.
-
- Trader
- Posts: 16342
- Joined: 08 Jun 2009, 09:51
- 80-90 Mem No: 6908
- Location: Surrey Syncronaut #156
- Contact:
Re: The T3200E thread
Finally, its got an exhaust! So once it stopped raining every weekend since its return, I took the pupes off and got engine mockup out to get it all clean and the final build actually happening.
After yet more cleaning, I found that both heads are stamped 15,0 (15.0) which should be the combustion chamber cc. It needs checking but should give a SCR of about 10.3:1 with DJ pistons (aka the full S spec) which with the cam and exhaust should give a solid 180PS and 280Nm, maybe 190/300...
After yet more cleaning, I found that both heads are stamped 15,0 (15.0) which should be the combustion chamber cc. It needs checking but should give a SCR of about 10.3:1 with DJ pistons (aka the full S spec) which with the cam and exhaust should give a solid 180PS and 280Nm, maybe 190/300...
-
- Trader
- Posts: 16342
- Joined: 08 Jun 2009, 09:51
- 80-90 Mem No: 6908
- Location: Surrey Syncronaut #156
- Contact:
Re: The T3200E thread
Volumes check out. 15cc chamber +7.5c in the fire ring volume ( 1.1mm used/compressed ring) = 22.5cc and a new WR7DC+
-
- Trader
- Posts: 16342
- Joined: 08 Jun 2009, 09:51
- 80-90 Mem No: 6908
- Location: Surrey Syncronaut #156
- Contact:
Re: The T3200E thread
Something that I rather wish I hadn't started but it is coming together now. A lot of dressing and faff!
These are oil windage plates, mostly to prevent the crank from throwing excessive amounts of oil up the 4/5/6 side pushrod tubes and filling the rocker box at higher rpm but also useful for generally keeping the oil in the sump when cornering hard or when on side slopes.
These will be fixed to the horizontal baffle plate.
These are oil windage plates, mostly to prevent the crank from throwing excessive amounts of oil up the 4/5/6 side pushrod tubes and filling the rocker box at higher rpm but also useful for generally keeping the oil in the sump when cornering hard or when on side slopes.
These will be fixed to the horizontal baffle plate.