Dashboard screws
Moderators: User administrators, Moderators
-
- Registered user
- Posts: 1828
- Joined: 16 Sep 2013, 17:19
- 80-90 Mem No: 13596
- Location: Hampshire
Dashboard screws
At some time I need to remove the dashboard if I want to repair the heater blower, two screws near the windscreen refuse to move even with a lot of plus gas and other re-lease fluids being applied, I can get a fairly good purchase with a screw driver but no movement, the windscreen does restrict it a bit. Not going to remove windscreen but wish when it was last replaced I gave the screws a go then, however the blower was working then so did not occur to me. Any other ideas would be welcome, not in a rush as can live with blower not operating as windscreen remains clear at all time and in all weathers.
1984 Campervan 1.9DG Petrol WBX
-
- Registered user
- Posts: 1911
- Joined: 10 Aug 2019, 23:30
- 80-90 Mem No: 17004
- Location: Coventry
Re: Dashboard screws
I found using a screwdriver with a long spanner on the end of it worked. I took the dash screws out of my syncro today, they were rusted in good. But with some pressure on the screwdriver and working the spanner to and fro got them moving.
1985 LeisureDrive 2.1DJ 5 Speed syncro conversion project.
1979 LT 2.0CH Westy project
1979 LT 2.0CH Westy project
-
- Registered user
- Posts: 1828
- Joined: 16 Sep 2013, 17:19
- 80-90 Mem No: 13596
- Location: Hampshire
Re: Dashboard screws
Thanks, will try that, tried something similar but difficult to get the downward pressure whilst rotating to keep the driver in place.
1984 Campervan 1.9DG Petrol WBX
- Oldiebut goodie
- Registered user
- Posts: 7294
- Joined: 18 Apr 2008, 01:19
- 80-90 Mem No: 11135
- Location: Eastern Angle
Re: Dashboard screws
Impact driver with a very long bit and a 7lb hammer worked for me. Used carefully it can be done.
1.6D 2019 VW T-Cross
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
-
- Registered user
- Posts: 1911
- Joined: 10 Aug 2019, 23:30
- 80-90 Mem No: 17004
- Location: Coventry
Re: Dashboard screws
TONYT25T25 wrote: ↑16 Dec 2020, 22:09 Thanks, will try that, tried something similar but difficult to get the downward pressure whilst rotating to keep the driver in place.
All I did was put the palm of one hand on the end of the Screwdriver and leaned against it ( takes a bit of maneuvering in the cab ) then just rocked the screwdriver back and forth, once it gives you should be just able to use the screwdriver to shift em.
Make sure the screwdriver is a snug fit as well.
1985 LeisureDrive 2.1DJ 5 Speed syncro conversion project.
1979 LT 2.0CH Westy project
1979 LT 2.0CH Westy project
- slowcoach
- Registered user
- Posts: 1580
- Joined: 06 May 2010, 10:23
- 80-90 Mem No: 8892
- Location: West Yorkshire
- Contact:
Re: Dashboard screws
This is what I did. The impact drivers you hit with a hammer, not the electric power tool. Bosh boshOldiebut goodie wrote:Impact driver with a very long bit and a 7lb hammer worked for me. Used carefully it can be done.
===================
1984 TRAKKA Conversion Subaru EJ20 5 Speed
1984 TRAKKA Conversion Subaru EJ20 5 Speed
-
- Registered user
- Posts: 1828
- Joined: 16 Sep 2013, 17:19
- 80-90 Mem No: 13596
- Location: Hampshire
Re: Dashboard screws
Thanks to all for advice, another job I need to do amongst others.
1984 Campervan 1.9DG Petrol WBX