1.9 dg won't run

Big lumps of metals and spanners.

Moderators: User administrators, Moderators

Yetti85
Registered user
Posts: 8
Joined: 16 Mar 2014, 20:36
80-90 Mem No: 13285
Location: Saltash

1.9 dg won't run

Post by Yetti85 »

So here's the issue I changed the drivers side water jacket seal a couple weeks ago that was fine drove about 600 miles passenger side went so that's fine I'll do that side too so I did and now tha van won't run unless my foot is flat to the floor and it just ticks over and is only firing possibly on two cylinders.
When putting dolly back together I put the fuel pump pipes round the wrong way so the pump was sucking dry and wouldn't fire so today I put it back right but don't think there's enough fuel going through.
Also I decided against changing the seals on the bottom of the piston sleeve which I think was a mistake as I have some slightly emulsified oil in the passenger side rocker cover but not in the sump which I'm finding hard to understand why.
So any ideas would be most gratefully appreciated.

Thanks in advance

Steve

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: 1.9 dg won't run

Post by itchyfeet »

Assuming its rhd Possibly air leak on the vac servo pipe connection, seen it before on here, sucks in fresh air rather than air fuel on that side, see pic
Image
Im a believer in changing lower liner seals but im told they often are good to be left.
Sombody on here had that problem and it was a cracked head butd run it a while properly , if that head is not firing it wont get hot and dry out
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

Yetti85
Registered user
Posts: 8
Joined: 16 Mar 2014, 20:36
80-90 Mem No: 13285
Location: Saltash

Re: 1.9 dg won't run

Post by Yetti85 »

Thanks itchyfeet thinking about it now the clip didn't feel right when I put it back together this time it didn't really tighten up could I replace with a jubilee clip do you think? I will try the hose tomorrow after work.
I'm starting to have withdrawal symptoms from driving her it's been nearly two weeks now and now she's out of mot as well.

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: 1.9 dg won't run

Post by itchyfeet »

Yes jubilee clips should be fine.
Best test is to remove the pipe and plug the hole with your hand and a thick rubber glove or something, that proves 100% if its that or not, if nothing changes its not that
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

Yetti85
Registered user
Posts: 8
Joined: 16 Mar 2014, 20:36
80-90 Mem No: 13285
Location: Saltash

Re: 1.9 dg won't run

Post by Yetti85 »

Thanks again will try that as soon as I get home tonight. Fingers crossed it works.

clinning
Registered user
Posts: 83
Joined: 18 Aug 2013, 19:05
80-90 Mem No: 0

Re: 1.9 dg won't run

Post by clinning »

Had similar issues with mine, was multiple air leaks in the end. Took a price of washer jet tubing, stuck in me ear and went around the engine with other end. Inlet manifold, carb gaskets etc. Also replaced my coil as was old and over heating. After that seemed to do the trick. Gaskets cheap enough to.
1984 Devon 1.9 DG

Yetti85
Registered user
Posts: 8
Joined: 16 Mar 2014, 20:36
80-90 Mem No: 13285
Location: Saltash

Re: 1.9 dg won't run

Post by Yetti85 »

Thanks clinning will try that too I haven't actually made it back to her this week to even look at but tomorrow is the day when I have a day off at last.

Yetti85
Registered user
Posts: 8
Joined: 16 Mar 2014, 20:36
80-90 Mem No: 13285
Location: Saltash

Re: 1.9 dg won't run

Post by Yetti85 »

Well I'm still stumped no air leaks loads of fuel spark but still only firing on cylinders 1 and 2 and won't won't rev :evil:

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: 1.9 dg won't run

Post by itchyfeet »

Ok you just removed head 3&4 so did you set the tappet preload? Valves may not be opening if not
also possible to get the pushrod on the edge of the lifter by mistake, you can set the preload but when you crank it pops into the lifter then there is a gap so valve wont open

deffo got 3&4 spark leads on right?
pull the plugs if they are dry its no fuel, if wet the leads are suspect

if you have a compression guage great, test it it will tell you if those cylinders/valves are working
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

Yetti85
Registered user
Posts: 8
Joined: 16 Mar 2014, 20:36
80-90 Mem No: 13285
Location: Saltash

Re: 1.9 dg won't run

Post by Yetti85 »

No I didn't set the tappet preload I just unbolted the lifters and bolted back on same as what I did with the over side and that side worked lovely.

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: 1.9 dg won't run

Post by itchyfeet »

Well it will probably be close but you should reset when the head comes off
id be doing it both side and checking compression if you dont have a guage get one, cheap enough and a must have tool for people like you prepared to diy :ok
Preload adjustment is in haynes
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

Yetti85
Registered user
Posts: 8
Joined: 16 Mar 2014, 20:36
80-90 Mem No: 13285
Location: Saltash

Re: 1.9 dg won't run

Post by Yetti85 »

:ok Thanks I have ordered a compression test and will defo reset tappets and check push rods in case I haven't seated them correctly and maybe bent one....

Will keep posted

Yetti85
Registered user
Posts: 8
Joined: 16 Mar 2014, 20:36
80-90 Mem No: 13285
Location: Saltash

Re: 1.9 dg won't run

Post by Yetti85 »

So compression test done and no compression in 3&4 really confused now only thing I can think of doing is taking head off and having it crack tested. Just don't know what to do for the best....

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: 1.9 dg won't run

Post by itchyfeet »

No compression 3 ans 4 possibly means valves are not closing or not opening
have you backed off the preload screws and reset preload?
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

Yetti85
Registered user
Posts: 8
Joined: 16 Mar 2014, 20:36
80-90 Mem No: 13285
Location: Saltash

Re: 1.9 dg won't run

Post by Yetti85 »

No not yet bit difficult to find instructions on how too. Especially whilst my two children are running around my ankles asking what's this what you doing and why? So I gave up but gonna go back to it when the wife is home shortly.

Does it matter what way the push rods go back in?

Locked