Just wondering????? need to do mine
Sven
Why do i have to soak my new starter motor bush in oil.
Moderators: User administrators, Moderators
-
- Registered user
- Posts: 119
- Joined: 11 Oct 2005, 08:34
- 80-90 Mem No: 997
- Location: Preston, Lancs
Why do i have to soak my new starter motor bush in oil.
Feeling like a freak on a leash
no. 997
svenlivesey@hotmail.com[img::]http://i126.photobucket.com/albums/p102 ... /flat4.jpg[/img]
no. 997
svenlivesey@hotmail.com[img::]http://i126.photobucket.com/albums/p102 ... /flat4.jpg[/img]
-
- Registered user
- Posts: 119
- Joined: 11 Oct 2005, 08:34
- 80-90 Mem No: 997
- Location: Preston, Lancs
hi Steve, ta for the quick reply. Is it to lubricate the bush??? and to keep friction down.....?
Thanks Sven
Thanks Sven
Feeling like a freak on a leash
no. 997
svenlivesey@hotmail.com[img::]http://i126.photobucket.com/albums/p102 ... /flat4.jpg[/img]
no. 997
svenlivesey@hotmail.com[img::]http://i126.photobucket.com/albums/p102 ... /flat4.jpg[/img]
- wasserleaker
- Registered user
- Posts: 106
- Joined: 23 Oct 2006, 19:23
- 80-90 Mem No: 3058
- Location: derby's. Caravelle Carat, 2.1 L.P.G'd DJ
- Contact:
some bushes are made from a sintered metal called 'oilite' ( metal dust basically, sometimes with graphite added, bound together under massive pressure) and these are porous, and will hold oil if left soaking in it.
we use phosphor bronze at work and i machine plain bearings/bushes out of it from solid bar stock, but i dont think this stuff is porous, i think its just a good load bearing friction reducing material, but oil or grease obviously helps as well
we use phosphor bronze at work and i machine plain bearings/bushes out of it from solid bar stock, but i dont think this stuff is porous, i think its just a good load bearing friction reducing material, but oil or grease obviously helps as well
-
- Registered user
- Posts: 4
- Joined: 02 May 2007, 00:07
- 80-90 Mem No: 4523
- Location: AYR SCOTLAND
phosphorus bronze
ive been using phos/bronze for a good few years as uprated spigot shaft bearings and have never had any drying up problems or screeching noises according to the engineer i use this material is self lubricateing
I WILL GET THERE IN THE END
-
- Trader
- Posts: 3045
- Joined: 08 Oct 2005, 19:36
- 80-90 Mem No: 1
- Location: Huddersfield, WeYo.
- Contact:
It isn't phosfor bronze, it is oylite.
this material is porous and does need to be soaked in oil to get it to be self lubricating for it's service life.
Another way of doing it is to place the bush on your thumb facing upwards, fill the bush with oil, put your forefinger over the open end and squeeze, you will see the oil seeping out of the sides of the bush.
This will save you soaking it for 24 hours!
this material is porous and does need to be soaked in oil to get it to be self lubricating for it's service life.
Another way of doing it is to place the bush on your thumb facing upwards, fill the bush with oil, put your forefinger over the open end and squeeze, you will see the oil seeping out of the sides of the bush.
This will save you soaking it for 24 hours!