rock n roll bed plans

Post by **kathyshack** » 07 Nov 2006, 11:40

has anyone got plans for making a rock n roll bed with jk hinges? I know in the past i have heard people have dimensions etc etc. would be great if anyone could e-mail me some....
thanks,
kathy

Post by **OLD ONE** » 07 Nov 2006, 11:52

GOT SOME. DONT KNOW IF THEY ARE JK, BUT MIGHT HELP..PM YOUR EMAIL ADDY. WILL SEND THEM

Post by **OLD ONE** » 07 Nov 2006, 12:33

Just sent. Hope it is of some help

Post by **kathyshack** » 07 Nov 2006, 14:54

Thanks Bob,
I think its reimo one though, so not sure if same as JK ones. Will take a clsoer look at it htough. - thanks!
Not sure still, whether to build one or go for one of the bluebird metal frame ones....
thanks again,
kathy

Post by **Dubkopfeyellow** » 08 Nov 2006, 13:36

We just made a bed out of JK hinges had to use the reimo plans but all worked out ok now the misses (who draws Assembly Instructions for furniture) is condsidering making a plan up for just this application

Just don't seem to be any anywhere that are that relevant!

Post by **Capt Jake** » 10 Nov 2006, 22:17

Have plans for a jk 3/4 if your still after one

Post by **Bowton Lad** » 10 Nov 2006, 22:30

Dubkopfeyellow wrote: all worked out ok now the misses (who draws Assembly Instructions for furniture) is condsidering making a plan up

Does 'er indoors work for MFI by any chance?

I've always wondered who was to blame for the drawings that look nothing like what you are trying to assemble......and then there's the instructions written in Hieroglyphics.

Post by **kathyshack** » 11 Nov 2006, 20:30

Capt Jake, that would be great, thanks

Post by **ermie571** » 13 Nov 2006, 08:50

Kathy,

we have just built the rnr bed from plans....They were all in german, and we only had a little bit of fiddling around to do when offering it up to the van.

I was really chuffed that it worked at all!

If there is anything I learned.....3 measures, one cut!!

The worst bit was getting the hinges bolted onto the upright supports in the right place. Had a couple of attempts, but got there in the end, with the assistance of a dob of paint on the end of a piece of wire to mark the position of the final hole....

But it works!!

Good luck

Emma

Post by **kathyshack** » 13 Nov 2006, 11:29

Thanks Emma,
I'm still in two minds whether to build one with JK hinges or to buy a bluebird one with the metal tubing. Not looking forward to drilling into the van though... don't want to drill into anything i shouldn't!

Post by **Zimbok** » 29 Dec 2006, 11:20

If anyone could e-mail the plans for the rock n roll bed I'd be very grateful. Thanks.

joneshow@gmail.com

Post by **lew** » 30 Dec 2006, 19:31

Zimbok wrote:If anyone could e-mail the plans for the rock n roll bed I'd be very grateful. Thanks.

joneshow@gmail.com

me too!!

theriff@jackassmail.com

Post by **ermie571** » 30 Dec 2006, 19:58

will nip upstairs and e-mail my plans to a moderator so they can go on the wiki...I am not capable!

Emma

x

Post by **Dubkopfeyellow** » 03 Jan 2007, 12:34

Bowton Lad wrote:
Dubkopfeyellow wrote: all worked out ok now the misses (who draws Assembly Instructions for furniture) is condsidering making a plan up

Does 'er indoors work for MFI by any chance?

I've always wondered who was to blame for the drawings that look nothing like what you are trying to assemble......and then there's the instructions written in Hieroglyphics.

No but her company does supply MFI I think (and they also do Instructions for other companies furniture too) so it could well be her fault although there instructions are pretty good

Post by **artymax** » 04 Jan 2007, 10:52

have they made it onto wiki yet? i'd really appreciate a copy if anyones got them? maxine.church@virgin.net thanks

Club 80-90 Forums