Page 1 of 1

Fitting a radio aerial

Posted: 21 Oct 2010, 12:37
by custardwaggonman
Hi all,

New T25 owner, first time poster, sorry for the divvy-ish question.

I want to fit a new radio aerial to my T25 but how do I access the hole on the passenger side to fit it? The only two ways in seem to be taking the headlight out or removing the dashboard. I have a working CD player fitted so hopefully it should just be a case of screwing in the new aerial and locating a trailing radio aerial at the back of the CD unit?

All tips and offers of help gratefully received!

Cheers

Re: Fitting a radio aerial

Posted: 21 Oct 2010, 13:05
by langb20
Hi,
On the existing aerial (assuming you have one), pop off the cover and unscrew the retainer screw, there will be a top mount also that you can probably slip the aerial out of. Then pull off the aerial and the wire that goes down into the pillar, what i'd do is attach a piece of string to the plug end (bit that goes into the back of the radio) first so when you pull the wire completely out, you can then attach the string to the new one and pull the string so it goes back the way it came - which is down the 'A' pillar and underneath the dash where the rest of the wires are. screw the new antenae to the bodywork and job done (or maybe even apply a cheeky bit of sealant for good measure) then have a cup of tea (with music on)
good luck,
Brent

Re: Fitting a radio aerial

Posted: 21 Oct 2010, 13:09
by Cruz
What kind of aerial is it? Is it pillar mounted (as described by the member above) or the standard fitting on the front panel?

Re: Fitting a radio aerial

Posted: 21 Oct 2010, 13:21
by custardwaggonman
Hi,
Thanks for the rapid replies.

Unfortunately, there's no aerial currently there - just a hole covered in gaffer tape. I do have the mounting (angled bit with black rubber base and fitting screw) which housed the old aerial - is this fitted externally without rooting around underneath?

Assuming I can find some kind of trailing aerial wire (are they purple?) from the back of the CD unit, is just a case of feeding this through the mass of wiring inside the dashboard or do I go in through the front grille?

Cheers

Re: Fitting a radio aerial

Posted: 21 Oct 2010, 13:46
by langb20
ah right, so behind the gaffer tape on the pillar you should have a 10mm round hole and a 2mm one. The plug end of the aerial goes in the 10mm hole, need to send it down the pillar and have someone grab the other end from under the dash and feed that over to your radio. the 2mm hole is where the screw goes in to hold the aerial to the bodywork. hope that makes sense

Re: Fitting a radio aerial

Posted: 30 Nov 2010, 14:11
by Funkyoid
I have a pillar mounted aerial and when I undid the screw the wire wasnt secured and it droped down, so nothing to attach a new one too!

How do you access the pillar, is it through the grill or do I need to fiddle in dash? Just don't want to start pulling dash if I can get to it via grill and headlight.

Any help would be really appreciated.

OH - my mate doesn't have an aerial so which would be best to install, a pillar mounted or a front mount. Can anyone recommend a pillar one to buy for me too and IF front mount is better one of those too?

Thanks

Beckie

Re: Fitting a radio aerial

Posted: 30 Nov 2010, 15:53
by 72BUG
I found the easiest way to get at it from the inside was to take the 2 rubber retaining straps off the glovebox so that it opens up all the way. With the glovebox out of the way I took the screws out of the fusebox and pushed it out of the way. I could then get my hand to the inside of the pillar where the ariel comes through to undo / re tighten the retaining screw. I did it on my own. No need for a second pair of hands.

Re: Fitting a radio aerial

Posted: 01 Dec 2010, 22:07
by Funkyoid
cheers for that, will give it a go at the wkend!

Re: Fitting a radio aerial

Posted: 30 Jan 2011, 14:07
by stephmac
Another handy topic

Re: Fitting a radio aerial

Posted: 31 Jan 2011, 10:47
by custardwaggonman
Hi all,

I followed 72 bug's advice and went in through the glovebox, then unscrewed the fuseboox and managed to fit it that way. No need to go the exterior route via grille etc

Result!

Thanks for all your ideas and help

John

Re: Fitting a radio aerial

Posted: 31 Jan 2011, 16:33
by 72BUG

Re: Fitting a radio aerial

Posted: 20 Mar 2011, 18:30
by Torkijo
langb20 wrote:Hi,
On the existing aerial (assuming you have one), pop off the cover and unscrew the retainer screw, there will be a top mount also that you can probably slip the aerial out of. Then pull off the aerial and the wire that goes down into the pillar, what i'd do is attach a piece of string to the plug end (bit that goes into the back of the radio) first so when you pull the wire completely out, you can then attach the string to the new one and pull the string so it goes back the way it came - which is down the 'A' pillar and underneath the dash where the rest of the wires are. screw the new antenae to the bodywork and job done (or maybe even apply a cheeky bit of sealant for good measure) then have a cup of tea (with music on)
good luck,
Brent


Hi

Did this today and worked a treat - but would add make sure you use decent string as mine got cut so had to open up dash to see where it was.

Re: Fitting a radio aerial

Posted: 21 Mar 2011, 12:37
by lloydy
I just fitted a brickwerks Ariel to the front panel of mine.
What i did was, remove headlight, remove cowl over speedo, feed Ariel down through gap behind speedo and aim for the hole behind headlight, once through I went around to front and pushed up through hole on front panel. The lead is then pulled through by pulling out ashtray and feeding lead into radio.
Seemed the only way possible on mine, due to length of Ariel.
Only took half hour at the most