Hi everyone, I recently did a front suspension overhaul on my 2WD T3.
New bushings everywhere (combo of Powerflex and OEM), new upper and lower balljoints.
I took the car to get an alignment, and was informed that they were unable to adjust the camber within spec. Apparently, a couple of different people at the shop looked at and indicated the same thing, that even though the eccentric washers were behaving as expected and changing the camber angle, it was not possible to get the vehicle within the required range.
I will go check out the vehicle on the lift this weekend, but wanted to enquire whether anyone has had a problem like this.
Thanks for the insights.
Camber adjustment not possible
Moderators: User administrators, Moderators
-
- Registered user
- Posts: 12
- Joined: 21 Aug 2020, 17:03
- 80-90 Mem No: 0
Camber adjustment not possible
1987 VW T3
1.7 KY 4 Speed Manual
1.7 KY 4 Speed Manual
-
- Registered user
- Posts: 1911
- Joined: 10 Aug 2019, 23:30
- 80-90 Mem No: 17004
- Location: Coventry
Re: Camber adjustment not possible
No clue myself, as I've been finding out at least around me there are few and far between places that have a clue about these vans.
1985 LeisureDrive 2.1DJ 5 Speed syncro conversion project.
1979 LT 2.0CH Westy project
1979 LT 2.0CH Westy project
- ZsZ
- Registered user
- Posts: 1412
- Joined: 12 Feb 2009, 16:28
- 80-90 Mem No: 14899
- Location: Budapest, Hungary
- Contact:
Re: Camber adjustment not possible
Do you have a lift/lowering spring? They need a bit different value than OE spec.
And are you sure the eccentric washer is facing the correct way. Fitted upside down can cause troubles.
And are you sure the eccentric washer is facing the correct way. Fitted upside down can cause troubles.
Zoltan
1986 Multivan ex-Caravelle. Van since 2006, running mTDi 1Z since 2008 with Fiat Croma 1.9 TDid pump 2008-2019, custom pump since 2019
5spd custom box 4.57 diff + 0.74 5th
1986 Multivan ex-Caravelle. Van since 2006, running mTDi 1Z since 2008 with Fiat Croma 1.9 TDid pump 2008-2019, custom pump since 2019
5spd custom box 4.57 diff + 0.74 5th
-
- Registered user
- Posts: 12
- Joined: 21 Aug 2020, 17:03
- 80-90 Mem No: 0
Re: Camber adjustment not possible
stock springs, Bilstein B4 Dampers.
I will check the eccentric washers.
I will check the eccentric washers.
1987 VW T3
1.7 KY 4 Speed Manual
1.7 KY 4 Speed Manual
- DoubleOSeven
- Registered user
- Posts: 2490
- Joined: 25 Jul 2014, 21:10
- 80-90 Mem No: 14520
- Location: Reading, England
- Contact:
Re: Camber adjustment not possible
It’s the same everywhere. Camber just doesn’t seem to register with fitting centres. Don’t know why. Do it yourself with a level?
1990 Volkswagen Transporter 2.1 Manual
2005 Porsche 911 3.6 Manual
2012 Volkswagen Polo 1.4 Automatic
2005 Porsche 911 3.6 Manual
2012 Volkswagen Polo 1.4 Automatic