Passat Alloys?
Moderators: User administrators, Moderators
-
- Registered user
- Posts: 1673
- Joined: 12 Oct 2005, 11:14
- 80-90 Mem No: 1342
- Location: Wolverhampton.
Re: Passat Alloys?
PCD?
Offset?
Needs to be 5x112 and between 30-39 I think, should be stamped on the wheel somewhere.
If it's over your looking at spacers and if it's under forget it.
Offset?
Needs to be 5x112 and between 30-39 I think, should be stamped on the wheel somewhere.
If it's over your looking at spacers and if it's under forget it.
2.1 DJ running on carb and LPG.
Re: Passat Alloys?
Thanks Shepster. I'll have a look.
-
- Registered user
- Posts: 536
- Joined: 02 May 2012, 17:48
- 80-90 Mem No: 11096
- Location: Sunny (?) Scarborough
Re: Passat Alloys?
They'd look better on my van Keith!
Owned by a 1983 Viking 2.0 Air-cooled and The Boy!
Re: Passat Alloys?
PCD is 5x100 near as damn it. Offset looks like 55 (does that sound correct?)
Oh well, not going on the van then! Back to plan A (the golf):roll:
Be a bit of work to do on them Stu. I reckon they are off an earlier Passat. Anyone want to buy a set of alloys
Oh well, not going on the van then! Back to plan A (the golf):roll:
Be a bit of work to do on them Stu. I reckon they are off an earlier Passat. Anyone want to buy a set of alloys
-
- Registered user
- Posts: 536
- Joined: 02 May 2012, 17:48
- 80-90 Mem No: 11096
- Location: Sunny (?) Scarborough
Re: Passat Alloys?
I've got a Passatt to add to those wheels when you sell them!!
Owned by a 1983 Viking 2.0 Air-cooled and The Boy!
-
- Registered user
- Posts: 635
- Joined: 11 Mar 2011, 15:59
- 80-90 Mem No: 9454
- Location: southampton
Re: Passat Alloys?
You could fit some 25mm 100 to 112 adapters and that would sort it and bring the offset down to 30.
Re: Passat Alloys?
kevtherev wrote:Do passats weigh in at 2 tonnes?
Hence my asking for advice in first post and Tech section.
-
- Registered user
- Posts: 1673
- Joined: 12 Oct 2005, 11:14
- 80-90 Mem No: 1342
- Location: Wolverhampton.
Re: Passat Alloys?
billybigspud wrote:You could fit some 25mm 100 to 112 adapters and that would sort it and bring the offset down to 30.
Is it worth the expence?
Sell 'em and get some with the correct PCD, adaptors are probably about £150 alone.
2.1 DJ running on carb and LPG.
Re: Passat Alloys?
Think you're right Shepster. Thanks for advice everyone. It wasn't the original idea to fit them to the van anyway, just an afterthought.shepster wrote:billybigspud wrote:You could fit some 25mm 100 to 112 adapters and that would sort it and bring the offset down to 30.
Is it worth the expence?
Sell 'em and get some with the correct PCD, adaptors are probably about £150 alone.
-
- Trader
- Posts: 1342
- Joined: 11 Oct 2005, 08:30
- 80-90 Mem No: 0
- Location: Barnsley...that's oop norf!
Re: Passat Alloys?
If they're from a Passat then they're 5X112.
The part number...behind the centre cap... will give all the correct info rather than any guess work.
The part number...behind the centre cap... will give all the correct info rather than any guess work.
There's no 'r' in bought!
Re: Passat Alloys?
didn't think to look there Steve Thanks for that.g60steve wrote:If they're from a Passat then they're 5X112.
The part number...behind the centre cap... will give all the correct info rather than any guess work.
The digits are 66-M15 LT2 and 1J0 601 149N AND they have the VW logo on them. Does that make any sense? Quick Googling of the part number says they are centre caps for 16" wheels. Jetta, Bora and Golf. No mention of Passat!!!
-
- Trader
- Posts: 1342
- Joined: 11 Oct 2005, 08:30
- 80-90 Mem No: 0
- Location: Barnsley...that's oop norf!
Re: Passat Alloys?
I meant the part number on the wheel itself behind the centre cap....like below.
Anyway...they are not 17" or from a Passat either....and definitely not suitable to be used on a T25....even with adaptors!
They are infact VW MK4 Golf/Bora/New Beetle Ronal 'Brands Hatch' alloys.
Part number: 1J0601025AE
5X100PCD
6.5"X16"
ET42
57mm centre bore.
Anyway...they are not 17" or from a Passat either....and definitely not suitable to be used on a T25....even with adaptors!
They are infact VW MK4 Golf/Bora/New Beetle Ronal 'Brands Hatch' alloys.
Part number: 1J0601025AE
5X100PCD
6.5"X16"
ET42
57mm centre bore.
There's no 'r' in bought!
- kevtherev
- Registered user
- Posts: 18830
- Joined: 23 Oct 2005, 20:13
- 80-90 Mem No: 2264
- Location: Country estate Wolverhampton Actually
Re: Passat Alloys?
Well that's pretty conclusive
Always admire your wealth of information Steve, is this freely available or do you have to know where to find it?
Always admire your wealth of information Steve, is this freely available or do you have to know where to find it?
AGG 2.0L 8V. (Golf GTi MkIII)