It’s high top off and under the high top it will be rotten as well.
Also if I was doing it again I’d get body cuts like this 274086012614 eBay
Search found 127 matches
- 23 Oct 2022, 19:56
- Forum: Bodywork, Seats & Glass
- Topic: Rain gutters
- Replies: 6
- Views: 802
- 07 Aug 2022, 15:38
- Forum: Mechanical
- Topic: Fuel tank
- Replies: 13
- Views: 414
Re: Fuel tank
Frost do all you need
I’d definitely treat the inside as well, ethanol in fuel will rust the tank out from the inside
I’d definitely treat the inside as well, ethanol in fuel will rust the tank out from the inside
- 06 Aug 2022, 11:56
- Forum: Campers
- Topic: Awning Repair Kit
- Replies: 1
- Views: 501
Re: Awning Repair Kit
You could try iron on repair fabric
- 17 May 2022, 21:40
- Forum: Mechanical
- Topic: 1.7ky won’t start.
- Replies: 13
- Views: 895
Re: 1.7ky won’t start.
loosened The fuel line nut on the injectors a bit get someone to turn the engine over when fuel comes out round the nut do the nut up then do the same on the other nuts as fuel comes out normally it will then start
- 17 May 2022, 13:43
- Forum: Mechanical
- Topic: 1.7ky won’t start.
- Replies: 13
- Views: 895
Re: 1.7ky won’t start.
Are you getting fuel at the injectors ?
- 14 May 2022, 13:17
- Forum: Mechanical
- Topic: Aaz 1 .9TD LHD handling in the wind
- Replies: 6
- Views: 313
Re: Aaz 1 .9TD LHD handling in the wind
Poly bush your steering rack and maybe your anti roll bar bushes.
i have A high top van it’s lowered and poly bushes alround and it still moves about with the wind and pass large Vehicles but it’s much better than it was.
also get a four wheel alignment done.
i have A high top van it’s lowered and poly bushes alround and it still moves about with the wind and pass large Vehicles but it’s much better than it was.
also get a four wheel alignment done.
- 20 Apr 2022, 14:08
- Forum: Bodywork, Seats & Glass
- Topic: Sliding door rollers and hinge
- Replies: 4
- Views: 511
Sliding door rollers and hinge
Hi my sliding door is a poor fit and rough on the rollers. should the bottom vertical roller be running in a groove/depression or should this be flat https://i.imgur.com/CyNUuk1.jpg https://i.imgur.com/bUdmvLr.jpg the middle hinge is there a kit to overhaul it and a roller kit for top middle and bo...
- 11 Apr 2022, 10:39
- Forum: T25 Alternative Engine Forum
- Topic: Oil catch can/ Provent
- Replies: 1
- Views: 443
Oil catch can/ Provent
Hi
I’m going to fit a oil catch can anyone got any experience in doing it and what one to go for?
I’m going to fit a oil catch can anyone got any experience in doing it and what one to go for?
- 11 Apr 2022, 10:20
- Forum: Mechanical
- Topic: Exhaust manifold gasket keeps burning out.
- Replies: 13
- Views: 662
Re: Exhaust manifold gasket keeps burning out.
Do you use a support from the turbo to the engine block this may help there’s a lot pulling down on the exhaust manifold, the turbo and the exhaust the one in the photo is home made not by me I still need to do it
- 02 Apr 2022, 15:33
- Forum: Bodywork, Seats & Glass
- Topic: N/S/R ply panel fixing point
- Replies: 9
- Views: 595
Re: N/S/R ply panel fixing point
It does have the lip I was planning on removing it the ply and covering would mean prying it out to much
- 02 Apr 2022, 08:52
- Forum: Bodywork, Seats & Glass
- Topic: N/S/R ply panel fixing point
- Replies: 9
- Views: 595
- 01 Apr 2022, 12:34
- Forum: Bodywork, Seats & Glass
- Topic: N/S/R ply panel fixing point
- Replies: 9
- Views: 595
Re: N/S/R ply panel fixing point
As pictured above. Panel vans, kombis and early caravelles had those lips welded to push the panel under. Late caravelles and multivans had those tabs with holes welded to push the plastic clips into. Ok thanks I’ll have to make them, any idea how far they stick out where the hole is.? cheers :roll...
- 01 Apr 2022, 09:54
- Forum: Bodywork, Seats & Glass
- Topic: N/S/R ply panel fixing point
- Replies: 9
- Views: 595
N/S/R ply panel fixing point
Hi I’m in the middle of fitting ply wood panel but can’t see any holes for the clips to go into on near side rear just 3 dimples which line up with the holes on the panel, is there some specific clip that glues in anyone got any photos of what should be there as a hole would probably letting water f...
- 31 Mar 2022, 08:38
- Forum: Bodywork, Seats & Glass
- Topic: New card doors - Plywood, varnish and PVA
- Replies: 22
- Views: 5774
Re: New card doors - Plywood, varnish and PVA
I got the door cards well a complete set apart from behind my cupboards and they where a poor fits had to sand the edges a lot to fit also sent the wrong sliding door card I have a 88 van and they sent a pre 85 one they will send me the 88 panel but want £35 to sent ended up make it myself
- 13 Mar 2022, 13:34
- Forum: Mechanical
- Topic: Multivan shocks
- Replies: 4
- Views: 329
Re: Multivan shocks
stephen t25 wrote: ↑13 Mar 2022, 10:23 Hi all,
Looking to get some new shocks for my Multivan, it has slightly lowered springs, any recommendations for a nice comfy ride.
Thanks