Search found 6118 matches
- 03 May 2024, 15:52
- Forum: Electrical & Instrumentation
- Topic: Help needed
- Replies: 8
- Views: 264
Re: Help needed
Sorry i want awake , and was getting frustrated …… i will remove my bit on the post
- 03 May 2024, 09:36
- Forum: Mechanical
- Topic: Failure of plastic gear linkage bush
- Replies: 3
- Views: 156
Re: Failure of plastic gear linkage bush
Where dis you buy it ? JK?
- 03 May 2024, 07:47
- Forum: Electrical & Instrumentation
- Topic: 1.9DG electrics
- Replies: 10
- Views: 179
Re: 1.9DG electrics
Morning
Engine bay loom is not that complicated , post some pictures of what you have got and im sure we can sort it out …..
Engine bay loom is not that complicated , post some pictures of what you have got and im sure we can sort it out …..
- 02 May 2024, 21:03
- Forum: Electrical & Instrumentation
- Topic: Help needed
- Replies: 8
- Views: 264
- 01 May 2024, 22:33
- Forum: Any Other Matters
- Topic: Knocking from ventilation system
- Replies: 21
- Views: 5392
Re: Knocking from ventilation system
Last time it did a heater motor it took me a full day from driving in to driving out , but that was only dash out , heater box out , swap the fan motor and put it back together , with several brews and tidying of bits under and around the dash …. I wasn’t rushing, nor charging by the hour , could we...
- 30 Apr 2024, 22:34
- Forum: Electrical & Instrumentation
- Topic: Headlight switch
- Replies: 10
- Views: 218
Re: Headlight switch
Have you checked the “x” relief relay ? And the ignition switch ?
- 30 Apr 2024, 21:31
- Forum: Mechanical
- Topic: Early Slding door Catch fouling on door card
- Replies: 19
- Views: 334
Re: Early Slding door Catch fouling on door card
You can swing the sliding door out of the way to adjust the hook , have a axle stand set at the height of the bottom of the door and roll it open until the middle hinge roller is at the gap in the track and lift it off and then the door will be out of the way and rest it on the axle stand , or remov...
- 30 Apr 2024, 18:18
- Forum: Mechanical
- Topic: Early Slding door Catch fouling on door card
- Replies: 19
- Views: 334
Re: Early Slding door Catch fouling on door card
The retaining stop is not stopping the hook ?
- 30 Apr 2024, 18:12
- Forum: Mechanical
- Topic: Van Running wierd (popping) and erratic rev counter
- Replies: 9
- Views: 211
Re: Van Running wierd (popping) and erratic rev counter
The fact the rev counter is erratic at the time the misfires happen says the coil is the first place to start looking, as the rev counter gets its signal from the coil directly
- 27 Apr 2024, 16:37
- Forum: Mechanical
- Topic: Clutch woes
- Replies: 5
- Views: 175
Re: Clutch woes
Quite possibly, personally i wouldnt buy a coffee from JK, it would turn out to be tea or muddy water when it arrived …. Brickwerks everytime
- 27 Apr 2024, 10:36
- Forum: Mechanical
- Topic: Clutch woes
- Replies: 5
- Views: 175
Re: Clutch woes
I suggest you haven’t got all the air out, or haven’t done the bleed screw up
- 27 Apr 2024, 00:54
- Forum: Any Other Matters
- Topic: T25 Log book change from minibus
- Replies: 9
- Views: 1669
Re: T25 Log book change from minibus
Much of the confusion comes from dvla and computers not recognising that “Caravelle” is a trim level pre 1992 and model post 1992 , which is a major issue with insurance companies , and is almost impossible to explain to them ….
Mini bus is incorrect but they won’t agree . Mpv is the way to go ……..
Mini bus is incorrect but they won’t agree . Mpv is the way to go ……..
- 25 Apr 2024, 21:43
- Forum: Mechanical
- Topic: Clunk when lifting the clutch... any ideas?
- Replies: 10
- Views: 320
Re: Clunk when lifting the clutch... any ideas?
can of beans in a cupboard? Ha, that brings to mind an incident from many years ago, when a long term experienced owner had a random knocking noise he couldn’t track down, driving him nuts it was….. well after many people had given advice , non of which led to the solving of the issue , we were on ...
- 24 Apr 2024, 17:36
- Forum: Mechanical
- Topic: Clunk when lifting the clutch... any ideas?
- Replies: 10
- Views: 320
Re: Clunk when lifting the clutch... any ideas?
I would say it must be internal to the gearbox if you have eliminated the engine mounts and the gearbox nose mount and you are sure there is no slack in the driveshaft CVs . There isnt anything else in the drive train . Maybe you need to get someone to look under whilst taking up the drive slack to ...
- 24 Apr 2024, 06:48
- Forum: Electrical & Instrumentation
- Topic: Idle problem now!
- Replies: 12
- Views: 397
Re: Idle problem now!
It hasn’t adjusted itself , So if it was oil, it wont be that ……
Rebuild kits are available from brickwerks …..
there are plenty of online articles of the setting up and working of the 2e3
Rebuild kits are available from brickwerks …..
there are plenty of online articles of the setting up and working of the 2e3