Search found 1052 matches
- 23 Dec 2019, 12:39
- Forum: T25 Alternative Engine Forum
- Topic: Which way to go ??
- Replies: 7
- Views: 2907
Re: Which way to go ??
I would repair the 1y and get to spend some time getting to know what you have bought before investing too much in a costly conversion, who knows you might even like the 1.9?
- 24 Oct 2019, 17:04
- Forum: Mechanical
- Topic: Rear Trailing Arm 2 piece Poly bush
- Replies: 24
- Views: 7286
Re: Rear Trailing Arm 2 piece Poly bush
I have replaced almost all my front bushes with Powerflex and I can honestly say I have not noticed any difference.
- 12 Jul 2018, 22:16
- Forum: Wheels & Tyres
- Topic: Fitting longer rear studs
- Replies: 10
- Views: 5685
Re: Fitting longer rear studs
Finally got them last week
- 09 Sep 2017, 18:31
- Forum: Mechanical
- Topic: Front wheel bearing
- Replies: 6
- Views: 2812
Re: Front wheel bearing
Wise decision I can't remember the number of cheap bearings I fitted before I got them from Brickwerks.
- 05 Aug 2017, 13:57
- Forum: Wheels & Tyres
- Topic: Fitting longer rear studs
- Replies: 10
- Views: 5685
Re: Fitting longer rear studs
Just re read the instructions on the Bricwerks page and if I read correctly it says you can hammer them in?
- 01 Jun 2017, 17:51
- Forum: Electrical & Instrumentation
- Topic: A different to the last post intermittent horn
- Replies: 7
- Views: 2474
Re: A different to the last post intermittent horn
New horn from Brickwerks works a treat, put a continuity test on the old one and it appeared to be dead tried it latter it was ok and again latter dead again, must have been an intermittent fault, thanks for the advice I think rewiring and a relay are in order.
- 31 May 2017, 21:10
- Forum: Electrical & Instrumentation
- Topic: A different to the last post intermittent horn
- Replies: 7
- Views: 2474
A different to the last post intermittent horn
I have a different intermittent problem that the horn will sound once and then no power is registering at the steering wheel or one side of the horn, there is power going in and sometimes on both sides but often only one, I have ordered a new horn from a reliable source the current one came from JK ...
- 28 May 2017, 20:47
- Forum: Bodywork, Seats & Glass
- Topic: MIG gas
- Replies: 2
- Views: 1236
MIG gas
Still trying to master this welding thing, currently pretty good at tacking but struggling to do continues seams, any way so far I have got through bottles of "hobby" gas in about 2 hours of welding am I doing something wrong?
- 06 May 2017, 17:47
- Forum: Bodywork, Seats & Glass
- Topic: Wheel arch replacement?
- Replies: 10
- Views: 3103
Re: Wheel arch replacement?
Thanks, as you say the original is much more solid than the replacement so I think cut and shut is the way forward, oh and it is diesel so need to remove the tank I hope.
- 06 May 2017, 14:48
- Forum: Bodywork, Seats & Glass
- Topic: Wheel arch replacement?
- Replies: 10
- Views: 3103
Wheel arch replacement?
Probably a silly question but here goes, I have rust around the filler cap proper push your finger through but the rest of the arch is pretty solid and rust free, I bought a repair panel and wondered if I cut out the rust could I just fit the whole panel over the top of the existing or should I just...
- 26 Feb 2017, 18:28
- Forum: Bodywork, Seats & Glass
- Topic: Disconnect Before Welding
- Replies: 11
- Views: 4082
Re: Disconnect Before Welding
I never disconnect the battery and not had any problems.
- 18 Feb 2017, 13:39
- Forum: Electrical & Instrumentation
- Topic: Heater fan problem
- Replies: 12
- Views: 4680
Re: Heater fan problem
I have managed 15 years without a blower, not worth the hassle for me
- 14 Feb 2017, 21:44
- Forum: Bodywork, Seats & Glass
- Topic: Rattles from dashboard
- Replies: 12
- Views: 3817
Re: Rattles from dashboard
My last mystery rattle that I only heard when breaking hard or pulling away sharply turned out to be two mugs I had left in the sink.
- 07 Feb 2017, 18:13
- Forum: Bodywork, Seats & Glass
- Topic: Fisher Price - My first welding and fabrication
- Replies: 40
- Views: 14190
Re: Fisher Price - My first welding and fabrication
I got some from Solent Body Supplies down by St Mary's not sure how that compares with Brundels?
- 02 Feb 2017, 11:48
- Forum: Electrical & Instrumentation
- Topic: Fluke 101
- Replies: 11
- Views: 3857
Re: Fluke 101
I got one of these after being recommended on here.
http://www.ebay.co.uk/itm/DIGITAL-LCD-M ... xyY9VRSfjY" onclick="window.open(this.href);return false;
http://www.ebay.co.uk/itm/DIGITAL-LCD-M ... xyY9VRSfjY" onclick="window.open(this.href);return false;