Search found 1052 matches

by kit
23 Dec 2019, 12:39
Forum: T25 Alternative Engine Forum
Topic: Which way to go ??
Replies: 7
Views: 1895

Re: Which way to go ??

I would repair the 1y and get to spend some time getting to know what you have bought before investing too much in a costly conversion, who knows you might even like the 1.9?
by kit
24 Oct 2019, 17:04
Forum: Mechanical
Topic: Rear Trailing Arm 2 piece Poly bush
Replies: 24
Views: 5444

Re: Rear Trailing Arm 2 piece Poly bush

I have replaced almost all my front bushes with Powerflex and I can honestly say I have not noticed any difference.
by kit
12 Jul 2018, 22:16
Forum: Wheels & Tyres
Topic: Fitting longer rear studs
Replies: 10
Views: 4367

Re: Fitting longer rear studs

Finally got them last week :)
by kit
09 Sep 2017, 18:31
Forum: Mechanical
Topic: Front wheel bearing
Replies: 6
Views: 2261

Re: Front wheel bearing

Wise decision I can't remember the number of cheap bearings I fitted before I got them from Brickwerks.
by kit
05 Aug 2017, 13:57
Forum: Wheels & Tyres
Topic: Fitting longer rear studs
Replies: 10
Views: 4367

Re: Fitting longer rear studs

Just re read the instructions on the Bricwerks page and if I read correctly it says you can hammer them in?
by kit
01 Jun 2017, 17:51
Forum: Electrical & Instrumentation
Topic: A different to the last post intermittent horn
Replies: 7
Views: 1900

Re: A different to the last post intermittent horn

New horn from Brickwerks works a treat, put a continuity test on the old one and it appeared to be dead tried it latter it was ok and again latter dead again, must have been an intermittent fault, thanks for the advice I think rewiring and a relay are in order.
by kit
31 May 2017, 21:10
Forum: Electrical & Instrumentation
Topic: A different to the last post intermittent horn
Replies: 7
Views: 1900

A different to the last post intermittent horn

I have a different intermittent problem that the horn will sound once and then no power is registering at the steering wheel or one side of the horn, there is power going in and sometimes on both sides but often only one, I have ordered a new horn from a reliable source the current one came from JK ...
by kit
28 May 2017, 20:47
Forum: Bodywork, Seats & Glass
Topic: MIG gas
Replies: 2
Views: 933

MIG gas

Still trying to master this welding thing, currently pretty good at tacking but struggling to do continues seams, any way so far I have got through bottles of "hobby" gas in about 2 hours of welding am I doing something wrong?
by kit
06 May 2017, 17:47
Forum: Bodywork, Seats & Glass
Topic: Wheel arch replacement?
Replies: 10
Views: 2352

Re: Wheel arch replacement?

Thanks, as you say the original is much more solid than the replacement so I think cut and shut is the way forward, oh and it is diesel so need to remove the tank I hope.
by kit
06 May 2017, 14:48
Forum: Bodywork, Seats & Glass
Topic: Wheel arch replacement?
Replies: 10
Views: 2352

Wheel arch replacement?

Probably a silly question but here goes, I have rust around the filler cap proper push your finger through but the rest of the arch is pretty solid and rust free, I bought a repair panel and wondered if I cut out the rust could I just fit the whole panel over the top of the existing or should I just...
by kit
26 Feb 2017, 18:28
Forum: Bodywork, Seats & Glass
Topic: Disconnect Before Welding
Replies: 11
Views: 3225

Re: Disconnect Before Welding

I never disconnect the battery and not had any problems.
by kit
18 Feb 2017, 13:39
Forum: Electrical & Instrumentation
Topic: Heater fan problem
Replies: 12
Views: 3886

Re: Heater fan problem

I have managed 15 years without a blower, not worth the hassle for me :run
by kit
14 Feb 2017, 21:44
Forum: Bodywork, Seats & Glass
Topic: Rattles from dashboard
Replies: 12
Views: 3138

Re: Rattles from dashboard

My last mystery rattle that I only heard when breaking hard or pulling away sharply turned out to be two mugs I had left in the sink.
by kit
07 Feb 2017, 18:13
Forum: Bodywork, Seats & Glass
Topic: Fisher Price - My first welding and fabrication
Replies: 40
Views: 11763

Re: Fisher Price - My first welding and fabrication

I got some from Solent Body Supplies down by St Mary's not sure how that compares with Brundels?
by kit
02 Feb 2017, 11:48
Forum: Electrical & Instrumentation
Topic: Fluke 101
Replies: 11
Views: 3141

Re: Fluke 101

I got one of these after being recommended on here. :ok

http://www.ebay.co.uk/itm/DIGITAL-LCD-M ... xyY9VRSfjY" onclick="window.open(this.href);return false;