Club 80-90 Forums

part number is 251 411 063 A they have gone obsolete from VW, post in the wanted section for a breaker to find you one. Be aware there are I think 2 thicknesses of pipe 21 and 19 mm although I think this part is the same for both just the rubber bush changes. (which you can get from Brickwerks.) th...

Thanks Jonnyb416

Ok here's a couple of photos of the part I need to source...

http://s1086.photobucket.com/albums/j457/nickster72/

Hello everyone, I've removed the anti roll bar from my 1980 T25, the bar is in good condition, the bushes will need to be replaced no worries there but the D shaped clamp which holds the anti roll bar on one side is badly corroded and has a large rust hole in it. I've looked at all the usual places ...

Thanks for your advice. I replaced both the speedo cable and centre cap as they were both worn. My speedometer now works properly :) However having replaced the centre cap I have realised that it is meant to be for the T2 as it protrudes further out so now I can't put my hub cap back on that wheel d...

Hi Paul, I'm also looking at my wiring, I bought my Devon last year and it has some wiring from leisure battery but I havent got round to replacing it yet. I have the white box you mentioned it sounds all very familiar At the moment I have a leisure battery connected to a some dodgy looking clips, t...

Thanks for the advice, i'll take a look at the weekend, it's too dark in the evenings at the moment

Hello everyone, Well I was happily driving along the other day, open roads nice sunshine and then suddenly I start hearing this clicking coming from my instrument panel. As few miles later and I noticed the speedo needle jumping erractially, this went on few about half a mile and then the needle wen...

I have the same problem, I was considering buying the 8 pack of white ones JK sell for £4.50 and then spraying them black. But I'm pretty sure that wouldn't look as good.

I suppose I'll have to have a hunt around at some VW Shows

Hi all, can you help me ? My father-in-law has a T25 Transporter that he wants to install a rer wiper into the tailgate. We have the wiper motor but we're having trouble working out exactly where we need to drill the hole for the spindle to go through the tailgate AND what size hole to drill. Measur...

So looks like installing in the engine compartment is the way to go.

Thanks for all your advice, thanks batmangb for the pics certainly seems like the best plan

Firstly sorry if this question has already been posted but I couldn't find it for looking I'm planning on fitting an electrical hook-up to my T25, but I really don't want to have to cut a hole in the side of my vehicle. I've seen posts about installing a hook-up in the rear oil flap but I don't like...

What engine? is it standard or modified? a jolly good service and set up should help..... a rolling road session will be a costly way to diagnose a problem that may not be fixable by them or a simple fix a service and set up item by a knowledgable mechanic would have cured.... Its a 1980 2ltr AC, i...

Hi,

Can anyone recommend a rolling road in Kent or East Sussex, would prefer to use a company nearer East Sussex don't know why just don't like going too near London

Too many horses have left my T25 for another stable !!

Any tips or suggestions would be very welcome

Ta

My hightop is a 1981 but I guess that the bunks would be pretty similar. The extra board is just a piece of 25mm plyboard with a small strip of wood either end to prevent it slipping off the rails. It has a 2inch thick mattress of foam which is cloth covered. Its about 2ft wide but not exactly sure...

My hightop is a 1981 but I guess that the bunks would be pretty similar. The extra board is just a piece of 25mm plyboard with a small strip of wood either end to prevent it slipping off the rails. It has a 2inch thick mattress of foam which is cloth covered. Its about 2ft wide but not exactly sure...